Ridgid R860443 18-VOLT CORDLESS COMPACT ROUTER User Guide
OPERATION
It is recommended that you do not exceed 1/8 in. depth of
cut in a single pass, regardless of the bit size or the softness
or condition of the workpiece. This will result in a higher
quality cut.
NOTE: To set the zero reset function to zero while the bit
is at zero depth, hold the micro depth adjustment knob in
place and rotate the zero reset function ring until it reads
“0”.
To make deeper cuts, it is necessary to make as many
successive passes as required, lowering the bit 1/8 in.
for each new pass. To save time, perform all the cutting
necessary at one depth setting, then lower the bit for the
next pass. This will assure uniform depth when the final
pass is completed.
NOTE: One full revolution of the micro depth adjust knob
moves the router housing 1/16 in.
Remove the router from the work surface.
Using the micro depth adjustment knob, adjust the
position of the bit to obtain the desired depth of cut. To
move the bit down, turn the micro depth adjustment knob
toward the down indicator arrow to the side of the knob.
WARNING:
Always observe the 1/8 in. MAX depth of cut per pass
If the desired depth of cut is greater than can be
safely cut in one pass, make cuts in two or more
passes. Do not remove more than 1/8 in. in a single
pass. Excessive depth of cut can result in loss
of control and the possibility of serious personal
injury.
rule when cutting.
NOTE: A reference depth scale is located on the motor
housing which can be used to measure depth of cut.
Each mark on the scale indicates a 1/16 in. change in
depth setting. Use the top edge of the removable base
as reference when setting depth of cut.
SETTING DEPTH OF CUT
See Figure 14, page 14.
WARNING:
Avoid open area of router base. Serious personal
injury will result from contact with a rotating bit.
Remove the battery pack.
Pull the quick release lever to the open position to free
the motor housing in the base.
USING EDGE GUIDE
Depress and hold the motor release lever.
See Figures 15 - 16, page 14.
NOTE: Large depth of cut adjustments can be made
using the motor release lever and positioning the motor
housing by moving it in the base by hand.
Use the edge guide to trim or cut a straight or curved edge.
NOTE: To use the edge guide with the vacuum adaptor,
install the adaptor first and then attach the edge guide.
With the desired bit installed into the collet and tightened
securely, slide the motor housing section of the router
upward in the base until the tip of the bit is just above
the work surface (bottom surface of subbase) by 1/4 in.
minimum. Release the motor release lever once the bit
is positioned above the work surface.
Remove the battery pack.
Thread guide bars into the base and tighten with a flat
head screwdriver.
Slide the edge guide onto the guide bars.
Install thumb screws provided into the edge guide.
Turn the micro depth adjustment knob slowly clockwise to
lower the bit slowly towards the work surface. The depth
of cut is considered “zero” when the bit just touches the
work surface.
Measure the proper distance to offset the bit, or if
trimming, position the bit at the edge of the workpiece.
Tighten the two thumb screws to secure the edge guide.
Reinstall the battery pack.
Move the router along the workpiece keeping the edge
guide in constant contact with edge of the workpiece.
10 - English
| General | Details |
|---|---|
| Name | Ridgid R860443 18-VOLT CORDLESS COMPACT ROUTER User Guide |
| Make | RIDGID |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.35 MB |
(1 votes, average: 5.00 out of 5)
Loading...
If you have any questions regarding Ridgid R860443 18-VOLT CORDLESS COMPACT ROUTER User Guide, please ask here and describe the problem in detail.
GL iNet AX1800 Slate AX Wireless Router User Manual
DrayTek Vigor2766 Series Fast Security Router User Guide
NOKIA FRRX504C 5G Field Router User Guide
QiXiang QX520 Dual SIM Router User Guide
NETGEAR RAX10 AX1800 WiFi 6 Router User Guide
DBIT AC1200 Dual Band WiFi Router Instructions
HOLZMANN MASCHINEN OBF1200_230V Hand Held Devices Router User Manual
Juniper ACX7509 Cloud Metro Router User Guide
TP-Link TD-W8951ND Wireless DSL Modem Router Installation Guide
LINKSYS E2500 Dual Band Router User Guide