CISCO RV320 Gigabit Dual WAN VPN Router User Guide
DMZ/WAN—Lit when a device is connected to the DMZ/WAN port.
Flashes when sending or receiving data over the WAN DMZ port.
LINK/ACT—Lit steady when a link between a port and another device is
detected. Flashes when a port is passing traffic.
GIGABIT—Lit when another device is connected a port and a 1000 Mbps
link is established. Off when the connection speed is under 1000 Mbps or
no other device is attached to a port.
USB 1—Type A USB port that supports flash drives and 3G/4G/LTE USB
dongles. Caution: Use only the power supply provided with the device;
using another power supply might cause the USB dongle to fail.
RESET—Reboot or reboot and restore defaults:
•
•
To reboot the unit and retain the current configuration, press and hold
RESET for at least 3, but no more than 10 seconds, by using a paper
clip or a pen tip.
To reboot the unit and restore the factory default configuration, press
and hold in the RESET button for more than 10 seconds. Changes you
have made to the configuration of your device are lost.
Back Panel
POWER—Toggles power to the device on or off.
12VDC (2A)—Power port that connects the device to the provided
12VDC, 2 amp power adapter.
Side Panel
USB 2—Type A USB port that supports flash drives and 3G/4G/LTE USB
dongles. Caution: Use only the power supply provided with the device;
using another power supply might cause the USB dongle to fail.
6
Cisco RV320/RV325 Gigabit Dual WAN VPN Router Quick Start Guide
Connecting
4
You must connect a configuration terminal (PC) to the device by using a
LAN port. The terminal must be in the same wired subnetwork as the
device to perform the initial configuration. As part of the initial
configuration, the device can be configured to allow remote management.
To connect a computer to the device:
STEP 1 Power off all equipment, including the cable or DSL modem, the
computer, and this device.
STEP 2 Use an Ethernet cable to connect your cable or DSL modem to the
WAN port on this device.
STEP 3 Connect another Ethernet cable from one of the LAN (Ethernet)
ports to the Ethernet port on the computer.
STEP 4 Power on the WAN device and wait until the connection is active.
STEP 5 Connect the power adapter to the 12VDC port of this device.
CAUTION
Use only the power adapter that is supplied with the device.
Using a different power adapter could damage the device or
cause the USB dongles to fail.
The POWER switch is on by default. The power light on the front
panel is lit when the power adapter is connected properly and the
device is finished booting.
STEP 6 Plug the other end of the adapter into an electrical outlet. Use the
plug (supplied) specific to your country.
STEP 7 Power on the computer that you connected to the LAN port in
Step 3. Your computer becomes a DHCP client of the device and
receives an IP address in the 192.168.1.xxx range.
Cisco RV320/RV325 Gigabit Dual WAN VPN Router Quick Start Guide
7
| General | Details |
|---|---|
| Name | CISCO RV320 Gigabit Dual WAN VPN Router User Guide |
| Make | Cisco |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.15 MB |
If you have any questions regarding CISCO RV320 Gigabit Dual WAN VPN Router User Guide, please ask here and describe the problem in detail.

CISCO cBR Series Converged Broadband Router User Guide

Cisco Router RV345 / RV345P User Guide

Cisco RV160W Router User Guide

Cisco RV260W Router User Guide

Cisco RV260P Router User Guide

Cisco RV320 Small Gigabit Dual WAN VPN Router User Manual

Cisco RV160 Router User Guide

Cisco Router RV345/RV345P User Guide

cisco RV340 Router User Guide























