D-Link DSR-250V2 Unified Services Router Installation Guide

1

2

About This Guide  

This guide gives step by step instructions for setting up D-Link DSR-250V2  

Services Router. Please note that the model you have purchased may  

appear slightly different from those shown in the illustrations.  

Device Status LEDs and Ethernet Port LEDs  

Installing and Connecting the Device  

Link  

TX/RX  

Status  

This chapter describes how to connect cables and power to the device.  

Speed  

Before You Begin  

Observe the following precautions to help prevent shutdowns, equipment  

failures and injuries:  

Figure 2. Ethernet RJ-45 Port LEDs  

Unpacking the Product  

The device LEDs show information about current device status. When the  

device power up, the POWER/STATUS LED will show solid orange during  

power on process. Startup takes one minute approximately to complete,  

the LED will change to solid green. If you want to turn the device off and on  

again, we recommend you wait a few seconds between shutting it down and  

powering it back. The Ethernet LEDs show the status of each Ethernet port.  

Table 2 lists the name, color, status and description of each device LED.  

Open the shipping carton and carefully unpack its contents. Please consult  

the packing list located in following information to make sure all items are  

present and undamaged. If any item is missing or damaged, please contact  

your local D-Link reseller for replacement.  

- Before installation, always check that the power supply is disconnected  

- Ensure that the room in which you operate the device has adequate air  

circulation and that the room temperature does Not exceed 40˚C (104˚F)  

- One (1) DSR-250V2 Unified Services Router Appliance  

- One (1) 12V/1.5A Power Adapter  

- One (1) Console Cable (RJ45-to-DB9 Cable)  

- Allow 3 inch of clear space to the front and back of the device.  

- Do not place the device in an equipment rack frame that blocks the air  

vents on the sides of the chassis. Ensure that enclosed racks have fans  

and louvered sides.  

- One (1) Ethernet (CAT5 UTP/Straight Through) Cable  

LED Indicators Color  

Status  

Description  

Quick Installation Guide  

Unified Services Router  

Power / Status Orange/Green/Red Solid Orange  

Device during power-on process  

Completion of power on  

Factory Reset  

Product Overview  

This chapter provides detailed descriptions of the DSR-250V2 device and  

its components.  

- Correct these hazardous conditions before any installation: moist or  

wet floors, leaks, ungrounded or frayed power cables, or missing safety  

grounds.  

Solid Green  

Solid Red  

This document will guide you through the  

basic installation process for your new  

D-Link Unified Services Router.  

Blinking Red  

Light Off  

Firmware upgrade  

The device is power-off  

No Link.  

Front Panel  

Connecting Power and Turn the Device On/Off  

TX/RX Status  

LINK Speed  

Green  

Light Off  

DSR-250V2  

The AC/DC Power Adapter shipped with the device connects the device to  

earth ground when plugged an AC grounding-type power outlet. The device  

must be connected to earth ground during normal operation.  

Solid Green  

Link present.  

Blinking Green Port is sending or receiving data.  

Green/Orange  

Solid Orange  

Solid Orange  

Solid Green  

Port is operating at 10Mbps.  

Port is operating at 100Mbps  

Port is operating at 1000Mbps  

To connect power to the device, plug the AC/DC power adapter into the DC  

power phone jet on the back panel of the device.  

Note: We recommend using a surge protector for the power connection.  

A

C

D

E

B

Table 2: Device Status LED Descriptions  

Figure 1. DSR-250V2 Front Panel  

To power on the DSR-250V2 device, press the DC power switch on the rear  

panel to the on position. To power off the device, press the power switch to  

the off position.  

Item Feature  

Description  

DSR-250V2 Default Interface Settings  

A

B

LED (Top to bottom)  

USB Port (1)  

Power LED: Indicates the Services Router is powered on.  

It can support various USB 2.0, 3.0 devices below:  

1.Flash Disk or Hard Disk for network sharing.  

2.Printer (It will be supported by future firmware upgrade)  

Ethernet  

Interface  

Interface  

Type  

IP Address  

Web-Based  

DHCP Server  

Connecting the Device to a Network  

Management  

This section provides basic information about physically connecting the  

DSR-250V2 to a network. To connect the necessary cables as shown in  

Figure 3.  

LAN(1-4)  

WAN  

Static IP  

192.168.10.1 Enabled  

Disabled  

Table 3: Default Interface Settings  

Enabled  

Disabled  

C

D

Gigabit LAN port (1-4) Connect Ethernet devices, such as computers, switches and hubs.  

Gigabit WAN port (1)  

One auto MDI/MDIX WAN ports are the connection for the Ether-  

net cable to the cable or DSL modem.  

DHCP Client 0.0.0.0  

1. Connect an RJ-45 cable from the port labeled WAN to the external  

router. The port WAN is pre-allocated to the WAN network segment.  

E

Console Port (1)  

Used to access Command Line Interface (CLI) via RJ45-to-DB9  

console Cable.  

Note: D-Link Services Routers only allow Web GUI access from LAN  

Table 1: DSR-250V2 Front Panel Descriptions  

interfaces by default for security reason.  

v1.01(WW)_90x130 2023/05/16 2907260025V2B11  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	D-Link DSR-250V2 Unified Services Router Installation Guide
Make	D-Link
Language	English
Filetype	PDF (Download)
File size	0.23 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL WI-FI INSTRUCTIONS & USER MANUALS
• D-Link

Questions and Answers (0)

If you have any questions regarding D-Link DSR-250V2 Unified Services Router Installation Guide, please ask here and describe the problem in detail.