LANCOM 1790VA-4G Router User Guide
Hardware
LANCOM 1790VA-4G
Power supply
12 V DC, external power adapter (230 V); bayonet connector to secure against disconnection
Gigabit Ethernet 10/100/1000
Power consumption Max. ca. 18 W
Environment
Housing
Temperature range 0–40 °C; humidity 0–95 %; non-condensing
Robust synthetic housing, rear connectors, ready for wall mounting, Kensington lock; mea-
sures 210 x 45 x 140 mm (W x H x D)
Config (Com)
VDSL / ADSL
ETH4
ETH3
ETH2
ETH1
DC 12V
Number of fans
Interfaces
1 quiet fan
a
b c
d
e f
g
WAN: VDSL2
a VDSL2 as per ITU G.993.2; profiles 8a, 8b, 8c, 8d, 12a, 12b, 17a, 35b
a VDSL Supervectoring as per ITU G.993.2 (Annex Q)
a Power
f ETH
a VDSL2 vectoring as per ITU G.993.5 (G.Vector)
a Compatible to VDSL2 from Deutsche Telekom
a Compatible to U-R2 from Deutsche Telekom (1TR112)
a ADSL2+ over ISDN as per ITU G.992.5 Annex B/J with DPBO, ITU G.992.3, and ITU G.992.1
a ADSL2+ over POTS as per ITU G.992.5 Annex A/M with DPBO, ITU G.992.3, and ITU.G.992.1
a Supports just one virtual connection at a time in ATM (VPI-VCI pair)
Off
Device switched off
Off
No networking device attached
Green, permanently*
Device operational, resp. device paired /
claimed and LANCOM Management Cloud
(LMC) accessible
Green, permanently
Connection to network device operational,
no data traffic
a
b
c
d
e
a
S I M
Green, flickering
Data transmission
Red / green blinking
Configuration password not set. Without a
configuration password, the configuration
data in the device is unprotected.
f
g 4G
ETH
4 individual ports, 10 / 100 / 1000 Mbps Gigabit Ethernet, by default set to switch mode.
Up to 3 ports can be operated as additional WAN ports. Ethernet ports can be electrically
disabled in the LCOS configuration.
Off
Cellular interface disabled
Connection to cellular network active
Cellular data transfer
Green, permanently
Green, flickering
Red blinking
Charge or time limit reached
1x green inverse
blinking*
Connection to the LMC active, pairing OK,
device not claimed
4G: Ant 1, Ant 2
Two SMA connectors for the supplied dipole rod antennas (LTE, UMTS), compatible LANCOM
AirLancer antennas for 4G or 3G, or from other manufacturers. Please respect the restrictions
which apply in your country when setting up an antenna system (in particular the antenna
gain and transmission power).
Orange, permanently Logon to cellular network successful
2x green inverse
blinking*
Pairing error, resp. LMC activation code
not available
Orange, blinking
Logging on to cellular network
Hardware error/module unavailable
SIM card error (PIN)
LTE / 4G antennas
Connect the two supplied cellular antennas to the connectors
at the side of the device.
Configuration interface
Red, permanently
Red / green, blinking
a
b
d
e
f
Config (Com) / V.24
Serial configuration interface/COM-port (8-pin mini-DIN): 9,600 - 115,200 baud, suitable for
optional connection of analog/GPRS modems. Supports internal COM-port server and provides
transparent asynchronous serial-data transfer via TCP.
3x green inverse
blinking*
LMC not accessible, resp. communication
error
Use a serial configuration cable to connect the serial interface
(COM) to the serial interface of the device you want to use for
configuring / monitoring (separately available).
Red / orange, blinking Uploading module firmware
b Online
WAN protocols
i VPN
VDSL / ADSL interface
Off
WAN connection inactive
VDSL, ADSL, Ethernet PPPoE, PPPoA, IPoA, Multi-PPPoE, ML-PPP, PPTP (PAC or PNS) and IPoE (with or without
DHCP), RIP-1, RIP-2, VLAN
LANCOM 1790VA-4G
Quick Reference Guide
Off
VPN connection inactive
VPN connection active
VPN connecting
Use the supplied DSL cable for the IP-based line to connect the
VDSL interface and the provider’s telephone socket. For more
information, please contact your Internet service provider.
Power
Green, blinking
WAN connection is established
(e.g. PPP negotiation)
Green, permanently
Green, flashing
After connecting the cable to the device, turn the bayonet
connector 90° clockwise until it clicks into place.
Use only the supplied power adapter.
Declaration of Conformity
Green, permanently
Red, permanently
WAN connection active
WAN connection error
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in
compliance with Directives 2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006.
The full text of the EU Declaration of Conformity is available at the following Internet address:
j Reset
Ethernet interfaces
Use the cable with the kiwi-colored connectors to connect one of
the interfaces ETH 1 to ETH 4 to your PC or a LAN switch.
c
Reset button
Operated e.g. with a paper clip
a short press: Restart the device
a long press: Reset the device
c DSL
SIM card slot (bottom side of the device)
Off
Interface deactivated
DSL connection active
DSL data transfer
Release the SIM-card holder and lever it upwards. Slide the SIM
card into the guide slot of the SIM-card holder. Press the holder
down until it clicks into place.
Package content
Green, permanently
Green, flickering
Red, flickering
Manual
Quick Reference Guide (DE/EN); Installation Guide (DE/EN)
1 Ethernet cable, 3 m (kiwi colored connectors); 1 DSL cable for an IP-based line, 4.25 m
2 LTE / 4G antennas
Cable
SIM
DSL transfer error
Antennas
Power adapter
Red / orange, blinking DSL hardware error
Orange, blinking DSL training
Orange, permanently DSL sync
External power supply adapter (230 V); 12 V / 2 A DC/S; barrel / bayonet (EU),
LANCOM item no. 111303 (not for WW devices)
Green, blinking
DSL connecting
Cloud-ready
Please observe the following when setting up the device
A Do not rest any objects on top of the device
A For devices to be operated on the desktop, please attach the
adhesive rubber footpads
A Keep the ventilation slots on the side of the device clear
of obstruction
A Rack installation with the optional LANCOM Rack Mount
(separately available)
A In case of wall mounting, use the drilling template as supplied
This product contains separate open-source software components which are subject to their own licenses, in particular
the General Public License (GPL). The license information for the device firmware (LCOS) is available on the device‘s
WEBconfig interface under “Extras > License information“. If the respective license demands, the source files for the
corresponding software components will be made available on a download server upon request.
*) The additional power LED statuses are displayed in 5-seconds
rotation if the device is configured to be managed by the LANCOM
Management Cloud.
4
Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.
| General | Details |
|---|---|
| Name | LANCOM 1790VA-4G Router User Guide |
| Make | LANCOM |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.13 MB |
(1 votes, average: 5.00 out of 5)
Loading...
If you have any questions regarding LANCOM 1790VA-4G Router User Guide, please ask here and describe the problem in detail.
LANCOM 883+ VoIP Single Site Router Installation Guide
LANCOM VPN 1793VAW Router Installation Guide
LANCOM 1781-4G VPN Router User Guide
LANCOM 884 VoIP Router User Guide
LANCOM 1793VA VPN Router User Guide
LANCOM 1793VAW VPN Router User Guide
MOFI NETWORK MOFI6500 4G LTE Router User Manual
NET MODULE NB1601 Router User Manual
HUAWEI B628-265 4G Router User Guide
TP-Link BE5000 Outdoor/ Mesh Wi-Fi 7 Router User Guide
ELPRO 641M-2 4G LTE Router Installation Guide
JUNIPER SSR1300 Session Smart Router User Guide
ASUS E20188 ZenWiFi XD4S Dual Band WiFi Router User Guide
TCL HH512LV Linkhub 5G WLAN Router User Guide
SKYWORTH GN630V GPON ONT WiFi Router Installation Guide
EDIMAX BR-6428NS V5 4 in 1 N300 WiFi Router Installation Guide