robustel R5020 5G WiFi Wireless Router Owner’s Manual
Robustel R5020 Hardware Manual
3. Reset Button.
Function
Operation
Reboot
Press and hold the RST button for 2~ 5 seconds under the operating status.
Restore to default
configuration
Restore to factory
default settings
Press and hold the RST button for 5~10 seconds, the RUN LED starts blinking quickly, the router will restore to default
configuration.
Once the operation of restoring default configuration is performed twice within one minute, the router will restore to factory
default settings.
Note: The more details please refer to RT123_SM_RobustOS Software Manual, 2.3 Factory Reset.
4. Ethernet Ports. There are four Ethernet ports on R5020, including ETH0 (Optional POE supported), ETH1,
ETH2, ETH3. The ETH0 on the router can be configured as a WAN port, while ETH1, ETH2 and ETH3 can only
be configured as a LAN port. By default, ETH1, ETH2 and ETH3 are lan0, and their IP are
192.168.0.1/255.255.255.0.
Ethernet LED Indicator
Status
Description
Link indicator
On, solid
On, blinking
Off
Connection is established
Data is being transferred
Connection is not established
(Yellow)
5. Digital IO & Serial Port. 2x5PIN 3.5mm pitch terminal block, 1 set of DO, 1 set of DI, 1 x RS232 and 1 x RS485.
DI signal access, can be used for NPN/PNP type sensor signal or switch signal acquisition. DO signal output,
can be used for NPN/PNP sensor control, please connect signals by referring to typical applications .
PIN
DI/DO
IGND
OGND
--
RS232
RS485
Direction
1
--
--
--
2
--
--
--
3
TXD
RXD
GND
--
--
Router Device
4
--
--
Router Device
5
--
--
--
--
--
--
--
--
6
IN
--
7
OUT
--
--
--
8
--
A
9
--
--
B
10
--
--
GND
Internal diagram of DI&DO
Typical Application:
DI connected with NPN sensor
DI connected with PNP sensor
DO Driven NPN Triode
DO Driven PNP Triode
Note: The external power supply DC voltage range is 3V~30V.
6. USB Interface.
Function
Operation
Firmware upgrade
USB interface is used for batch firmware upgrading, but cannot be used for sending or receiving data from slave devices which
connected to it. You can insert a USB storage device into the router’s USB interface, such as a U disk or a hard disk. If there have a
supported configuration file or a router firmware in this USB storage device, the router will automatically update the
configuration file or the firmware. For more details, please refer to RT123_SM_RobustOS Software Manual.
RT064_HM_R5020
7/10
| General | Details |
|---|---|
| Name | robustel R5020 5G WiFi Wireless Router Owner’s Manual |
| Make | robustel |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.33 MB |
(1 votes, average: 5.00 out of 5)
Loading...
If you have any questions regarding robustel R5020 5G WiFi Wireless Router Owner’s Manual, please ask here and describe the problem in detail.
robustel R5020 Lite 5G Router Instruction Manual
robustel R2010 Dual SIM VPN IoT Router Instruction Manual
robustel R1520LG Dual SIM LTE Router User Manual
robustel R2000 Dual SIM Cellular VPN Router Instruction Manual
robustel R3000 Lite Dual-SIM VPN Router User Manual
robustel R2011 Cellular Router Instruction Manual
robustel R1510 4G LTE Router User Manual
robustel R1510-4L VPN Router Owner’s Manual
Kangwei ZLT W304VA PRO WIFI6 Wireless Dual Band Router User Manual
KMC Controls BAC-5051 TRUEFIT Measurement System Router User Guide
JUNIPER NETWORKS PTX10004 Packet Transport Router User Guide
Amped Wireless R10000 High Power Wireless N 600mW Router User Guide
TP-Link ER706W Wi-Fi Router User Guide
TRENDNET AX1800 Dual Band Wifi 6 Gigabit Dual Wan VPN SMB Router User Guide
ZYXEL LTE3301-PLUS 4G LTE-A Router User Guide
REYEE RG-E6 WiFi 6 Router Installation Guide
SEALEY CP20VTR 20V SV20 Series Cordless Trimming Router Instructions
GL iNet XE3000 MBPS M519 Portable Router User Manual