SEALEY CP20VTR 20V SV20 Series Cordless Trimming Router Instructions

1

2

3

4

5

6

7

preventive safety measures reduce the risk of starting the power tool accidentally.  

Maintain tools and accessories. Check for misalignment or biding of the moving parts, breakage of parts and any other condition that  

may affect the tool’s operation. If damaged, have the tool repaired by qualified engineers before use.  

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier  

to control.  

Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for  

safe handling and control of the tool in unexpected situation.  

Hold the tool by insulated gripping surfaces only.  

9

9

9

9

7. INTRODUCTION  

Converts the CP20VTR Trimming Router into a plunge router. Sturdy construction thanks to the cast aluminium body and protective base sheet.  

Features precision depth adjustment as well as runners and clamps for the telescopic arms. Sturdy handles for comfort and control during use.  

Supplied with router guide, straight guide, two spanners and a safety guard.  

8. CONTENTS  

Note:  

See Parts list for  

item details.  

Body Lock Lever on  

reverse  

Spindle  

Spindle Register  

fig.9  

fig.8  

9. OPERATION  

9.1.  

9.1.1.  

In order to fit the plunge base you will have to remove the Tool base first (CP20VTR - fig.1)  

Open the lock lever of the base, then insert the tool into the router base aligning the groove on the tool with the protrusion on  

the router base.  

9.1.2.  

9.2.  

9.2.1.  

Close the lock Lever. To remove the base, follow the installation procedure in reverse order.  

INSTALLING OR REMOVING THE PARALLEL RULER ON THE PLUNGE BASE. (fig.8 fig.9).  

Insert the guide bars into the holes in the plunge base, and then tighten the wing bolts. To remove the ruler, follow the installation  

procedure in reverse.  

fig.10  

9.3.  

ADJUSTING CUTTING DEPTH (fig.11, 12, 13,14).  

NOTE: It is recommended that the maximum depth of cut in one pass is 3mm. Use more passes at 3mm increments if greater depth  

required.  

9.3.1.  

Fit router bit and use body lock lever (fig.8) to adjust body location within base to suit bit length and depth of cut required.  

NOTE: If the body is not secured after closing the lock lever, tighten the hex nut of lever assembly and then close the lock lever.  

9.3.2.  

9.3.3.  

9.3.4.  

9.3.5.  

Depress the Plunge Base until the bit touches the surface of the material to be worked and lock in position using the clamp lever.  

Rotate castellated positioning block (item 7) such that the required height level is located underneath the adjustment screw spindle.  

Lower adjustment spindle so that it touches the castellated block and slide the Indicator cup down to the zero position on the side scale.  

Set vernier to 0 and raise spindle so that the Indicator cup matches the scale to the depth of cut required i.e 3 mm graduations and lock in  

position.  

© Jack Sealey Limited  

Original Language Version  

CP20VTR Issue 1 15/02/2023  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	SEALEY CP20VTR 20V SV20 Series Cordless Trimming Router Instructions
Make	SEALEY
Language	English
Filetype	PDF (Download)
File size	0.4 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL WI-FI INSTRUCTIONS & USER MANUALS
• SEALEY

Questions and Answers (0)

If you have any questions regarding SEALEY CP20VTR 20V SV20 Series Cordless Trimming Router Instructions, please ask here and describe the problem in detail.