SKYWORTH R6215 Wi-Fi 6 Mesh Router Installation Guide
A, Setup Mesh AP with Wired Backhaul
Safety Instructions
Product Specification
Single device installation
The second device can be connected to the First device (Controller) through a Ethernet
cable as the picture shows:
Item
Specification
1. This equipment is a Class III electrical appliance which is designed to be supplied
from a separated/safety extra-low voltage (SELV) power adapter.
Product Name
WAN Interface
LAN Interface
Wi-Fi 6 Mesh Router
1*RJ45 Gigabit Ethernet Port
2*RJ45 Gigabit Ethernet Port
ISP Modem
2. WARNING: To reduce the risk of fire or electric shock, do not expose this device to
rain or moisture. The device shall not be exposed to dripping or splashing and that
objects filled with liquids, such as vases, shall not be placed on apparatus.
Mesh
Controller
ISP Modem
3. Mobile Phone
Connection
2.4GHz IEEE 802.11b/g/n/ax
5GHz: IEEE 802.11a/n/ac/ax
Wi-Fi Standard
Band
2. WAN
Connection
2. WAN
Connection
3. WARNING: the power plug/direct plug-in adapter is used as disconnect device, the
disconnect device shall remain readily operable.
2.4GHz and 5GHz dual-band concurrent
2.4GHz: 2x2
5GHz: 2x2
Power
Adapter
MIMO
Power
Adapter
4.
Correct Disposal of this product. This marking indicates that this product
should not be disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources. To return your used device, please use the
return and collection systems or contact the retailer or service operator where the
product was purchased. They can take this product for environmental safe recycling.
2.4GHz - 300Mbps(11n@40MHz)
574Mbps(11ax@40MHz)
5GHz - 867Mbps(11ac@80MHz)
1201Mbps(11ax@80MHz)
2402Mbps(11ax@160MHz)
1. Power
Connection
Data Rate (maximum)
Quick Installation Guide
1. Power
Connection
4. LAN
Connection
Antennas
5*internal Antennas (3dBi)
Mesh
Agent
The device works in router mode by default. Please follow the below steps to install
one single device:
Wi-Fi Mesh
Wi-Fi 6 Mesh Router
4. Ethernet Backhaul
Connection
5. For the terminals marked with symbol of
“
” may be of sufficient magnitude to
Wi-Fi Mesh Standard
Capacity
Wi-Fi Alliance EasyMesh
constitute a risk of electric shock. The external wiring connected to the terminals
requires installation by an instructed person or the used of ready-made leads or
cords.
(1) Connect power adapter,power ON the device and wait the system boot up.
Maximum 5 Nodes (1 controller + 4 agents)
Wired or Wireless auto-redundancy
Power
Adapter
Backhaul Type
(2) Connect WAN port of the device to your existing modem or router (Installed by
Service Provider previously and make sure the Indicator is on and blinking.
Environment
6.
This lightning flash with arrowhead symbol within
CAUTION !
RISK OF ELECTRIC SHOCK
Rated Power Input
Operating Temperature
Storage Temperature
Operating Humidity
12VDC/1.5A
(3) Wait a few seconds for the device to obtain the IP, after success the indicator will
light up and ON.
DO NOT OPEN
an equilateral triangle is intended to alert the user
1. Power
Connection
0 ~ 45 (32~113
)
to the presence of non-insulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
-20 ~ 65 (-4~149
)
If the indicator does not light up in step (3), please contact the service provider for
advice.
0 ~ 95% non-condensing
Warning: to reduce the risk of electric shock, do not remove cover (or back) as there
are no user-serviceable parts inside. Refer servicing to qualified personnel.
(4) Indicator is GREEN/BLUE on means that the device has been connected to the
network, and the user can start to surf the Internet. If need to add a mesh device,
please refer to the following steps.
Connect the RJ45 port of the second device to the First device (Controller) through an
cable. After two minutes, observe the indicator of the second device. When it stops
BLUE flashing and remains BLUE ON, the mesh networking is successful. the WiFi
configuration of the Controller will be synchronized to the second device.
Packaging Items
The exclamation point within an equilateral triangle is intended to alert the user to
the presence of important operating and maintenance instructions in the literature
accompanying the appliance.
Router
Mesh Wi-Fi 6 Router
7.
For the third or more device, it can be connected to the Controller or the second device
by the same method.
Multiple device installations for deploying mesh networks
Power Adapter
Ethernet Cable
Output 12VDC Power Adapter
When need to install multiple devices (Set up Mesh network) to increase the coverage
area to provide a better experience, you can refer to the description in this section.
8. Use only the AC adapter which is included in the product package. Any other
adapter may cause damage to the device. Such damage is not covered under
warranty.
Compared with the wireless connection, the wired connection is more stable.
After the mesh networking is successful, you can disconnect the Ethernet cable and
move the second device to the place for the need (the distance should not be too far, it
is recommended that the WiFi RSSI signal be within -65dBm), the Mesh backhaul will
automatically switch to wireless.
Standard CAT5e Ethernet cable
Firstly, please make sure the first device is installed and able to connect to the internet
normally (Refer to the installation steps for a single device).
Shenzhen Skyworth Digital Technology Co., LTD.
This guide provides basic product specification
and information for installing the device and
get it up and running on your home network
Quick Installation
Guide
14/F, Unit A, Skyworth Building, Gaoxin Ave.1.S., Nanshan District, Shenzhen, China
Then Power on the second device, there are multiple ways to help you build a mesh
network:
FCC Statement
B, Setup Mesh AP with Wireless Backhaul
Front Panel Indicators
Rear Panel Interfaces
Login Web Manager and Change Settings
Troubleshooting
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
The second device can be also connected to the Controller through Wireless as the
picture shows:
Trouble
Troubleshooting Tips
(1) How to Login the Mesh Controller’s Web Manager
Open a web browser and input the following text in address bar:
• Login the Controller’s web to make sure its role is
“Controller” and its indicator is ON.
Reset the 2nd router’s configurations to Factory
Default by pressing the RESET button for 10 seconds.
•
The second devices
cannot pair with the Mesh
Controller with Wireless
backhaul
Input default Username and Password, e.g. user/user
• Move the mesh router closer to the Controller.
• Follow the steps in section “Setup Mesh AP with
Wireless Backhaul”.
Note: you may also check the label at the bottom of the device for default IP and
username/password if the information above does not work.
ISP Modem
• If the 2nd router still can not pair with the Controller,
try Ethernet backhaul first then disconnect the
Ethernet cable and wait for 10 seconds.
-Reorient or relocate the receiving antenna.
2. WAN
Connection
3. LAN
Connection
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
(2) How to Change Web Login Password
Step1: Login the mesh Controller’s Web Manager
Step2: Click "System" icon
• Login the Controller’s web to make sure its role is
“Controller” and its indicator is On.
Power
Adapter
-Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modifications not expressly
approved by the party.
Mesh
Controller
• Reset the 2nd router’s configurations to Factory
Default by pressing the RESET button for 10 seconds.
The second device
cannot pair with the Mesh
Controller with Ethernet
backhaul
Step3: Click "User management" menu
Step4: Enter your old password and new password
Step5: Click on "Confirm" button to submit your change
(3) How to Change Wi-Fi SSID and Password
Step1: Login the Mesh Controller’s Web Manager
Step2: Click "WLAN" icon
1. Power
Connection
Connect WAN port of the 2nd router to the
•
Responsible for compliance could void the user’s authority to operate this equipment.
(Example- use only shielded interface cables when connecting to computer or
peripheral devices).
Controller’s LAN port and wait for about two minutes
and the 2nd router shall pair with the Controller
automatically and its indicator shall be BLUE On.
5. Wireless Backhaul
Connection
Indicators on Front Panel:
• If the issue still exists, please contact your service
provider for further help.
LED Color
Status
Off
Description
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
Power
Adapter
Off
The device is powered off
The device can not access the Internet
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
On
Mesh
Agent
4. Power
Connection
Step3: Click “EasyMesh” menu
Flashing
(Slow)
The device is booting
Red
Step4: Enter your new SSID and new Wi-Fi Key
Name
Color
Description
FCC Radiation Exposure Statement:
Flashing The device is restoring factory setting or upgrading the
(Fast)
Installation Steps:
Step5: Click on "Confirm" button to submit your changes, Wi-Fi configurations of
all router’s in the MESH will be changed
The equipment complies with FCC Radiation exposure limits set forth for uncontrolled
enviroment. This equipment should be installed and operated with minimum distance
20cm between the radiator and your body.
WPS pairing button, press 3 seconds to enable
pairing or mesh networking
firmware
WPS
White
Option-1: Connect through a network cable, and remove the network cable after
mesh networking is successful
The device can access the Internet or Mesh networked
successfully with the controller
On
Short press (1 second) for reset the router
Blue
Reset
Black
Long press (10 seconds) for reset to factory default
settings
Refer to the “Setup Mesh AP with Wired Backhaul” to complete the mesh networking,
and after that, disconnect the Ethernet cable, the Mesh backhaul will switch to the
wireless automatically.
The device is in the process of Mesh networking due to
WPS or APP
(4) How to Reset a Router’s Configurations to its Factory Default Settings
Flashing
On
Power on the router, press and hold the ‘RESET’ button at the rear panel of your
device for more than 10 seconds using the end of a paper clip or other small object
with a narrow tip such as a pencil, and then release.
12V DC
WAN
Black
Blue
DC Input Jack
The device can access the Internet but not Mesh
networked with the controller
WAN Port, used to connect network layer devices
or Controllers
Green
Option-2: Press WPS button
The device can access the Internet but not Mesh networked
with the controller. And all SSIDs are turned off
On
(1) Press the WPS button on the Controller for 3 seconds and release the button.
(2) Press the WPS button on the second device for 3 seconds.
LAN 1-2
Yellow
LAN Port connect to the back-haul or end user
(3) Observe the WPS indicator of the second device. Wait about 120 seconds till the
Indicator stops BLUE flashing and remains ON, then the mesh networking is
successful.
料号(Part No.):
待定
展开尺寸(Unfolding Size):
成品尺寸(Folded Size):
印刷颜色(Print Color):
材质(Material):
570x145 mm
95x145 mm
黑色(Black)
技术要求(NOTES):
80g书纸(80g Writing paper)
1: 公差(Tolerance): ±2mm
2: 原材料及后处理工艺均能满足ROHS和WEEE的要求.
(Raw materials and the corresponding post processing
should meet requirements defined in the ROHS and WEEE.)
厂家/Manufacturer: Voion/Fuweizhi/Jiahui
设计/Designer: 罗运鸿
日期/Date: 2023.09.08
认证加签/Certification Audit:
审核/Audit:
| General | Details |
|---|---|
| Name | SKYWORTH R6215 Wi-Fi 6 Mesh Router Installation Guide |
| Make | SKYWORTH |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.21 MB |
(1 votes, average: 5.00 out of 5)
Loading...
If you have any questions regarding SKYWORTH R6215 Wi-Fi 6 Mesh Router Installation Guide, please ask here and describe the problem in detail.
SKYWORTH GN630V GPON ONT WiFi Router Installation Guide
SKYWORTH GN543V GPON ONT WiFi Router Installation Guide
SKYWORTH GN630 GPON ONT Wi-Fi Router Installation Guide
BOSSPAC EA000405 Border Router Instruction Manual
ZEBRA ZT510 Router User Manual
BILLION MX-220-UT-5G Advanced 5G Router Installation Guide
robustel R2000 Dual SIM Cellular VPN Router Instruction Manual
Thumbnail TN1000 Master Router Instruction Manual
ozito PXBLTS Trim Router Instruction Manual
ASKEY EAO2522P-2 WiFi6 AP Outdoor 5G NR Router Installation Guide
REPUBLIC OF GAMERS GT-BE19000 WiFi 7 Tri Band Gaming Router User Guide
peplink MAX BR1 Pro 5G Pepwave Router User Manual
THOMSON TH4G300 4G LTE Router Instruction Manual