Tenda HG Series xPON ONT Network Router Installation Guide

1

2

Get to know the ONT  

LED indicators  

Ports/Buttons  

The LED indicators may vary with models. The actual product prevails.  

The ports and buttons may vary with models. The actual product prevails.  

LED indicator Color  

Status  

Description  

Port/Button  

Description  

Press the button to turn on or turn off the ONT.  

The ONT is powered on.  

The ONT is powered off.  

Solid on  

Off  

ON/OFF  

PWR  

INET  

Green  

Green  

PON  

PWR  

USB  

Optical fiber port. Used to connect to optical network through a fiber cord.  

Used to connect the ONT to a power source using the included power adapter.  

USB 2.0 port. Used to connect to a USB storage for resource sharing.  

The internet access is available through the ONT.  

Solid on  

Data is being transmitted through the ONT.  

Blinking  

Off  

No internet access is available through the ONT.  

Quick Installation Guide  

WLAN  

TEL  

Wi-Fi on/off button. Press the button to enable or disable the Wi-Fi function of the ONT.  

Telephone port. Used to connect to a telephone for voice service using a telephone cable.  

The ONT is registered successfully.  

The ONT is registering.  

Solid on  

Blinking  

Off  

PON  

Green  

HG Series xPON ONT  

The ONT is unregistered.  

LAN1-4  

Gigabit LAN ports. Used to connect to such devices as routers, switches, computers or IPTV  

set-top boxes.  

The received optical power is lower than the optical receiver sensitivity.  

The received optical power is at a proper value.  

Blinking  

Off  

LOS  

LAN  

Red  

WPS/Reset button.  

• WPS: WPS-supported devices can connect to the Wi-Fi networks of the ONT without entering  

the password through WPS negotiation.  

The LAN port is connected. No data is being transmitted.  

The LAN port is transmitting data.  

Solid on  

Blinking  

Off  

Green  

Press the button for about 1-3 seconds to start the WPS negotiation process of the ONT. The  

WPS (marked WLAN/2.4G/5G/WPS) LED indicator blinks quickly. Within 2 minutes, enable the  

WPS function to establish a WPS connection on a WPS-supported device.  

• Reset: Restore the ONT to the configurations preset by the ISP or restore the ONT to factory  

settings.  

The LAN port is disconnected.  

The ONT is registered with IMS. No data is being transmitted.  

The ONT is registered with IMS and is transmitting data.  

Solid on  

Blinking  

WPS/RST  

TEL  

Green  

- To restore the ONT to the configurations preset by the ISP: After the ONT completes  

startup, press the button for 10 to 60 seconds and release it. All LED indicators will light  

off in a few seconds. When the PWR LED indicator lights solid on again, the ONT is  

restored to the configurations preset by the ISP.  

The ONT is not registered with IMS.  

The Wi-Fi network is enabled.  

Off  

Solid on  

Data is being transmitted wirelessly.  

- To restore the ONT to factory settings: After the ONT completes startup, press the button  

for more than 1 minute and release it. All LED indicators will light off in a few seconds.  

When the PWR LED indicator lights solid on again, the ONT is restored to the factory  

settings.  

For the device without the WPS LED indicator: If the WPS function is  

activated on the device, the WLAN/2.4G/5G LED indicator blinking  

means that the device is performing WPS negotiation.  

WLAN/  

Blinking  

Green  

Package contents  

2.4G/5G  

• xPON ONT x 1  

The Wi-Fi network is disabled.  

Off  

• Power adapter x 1  

LED  

LED indicator on/off button. Press the button to turn on or off the LED indicators of the ONT.  

Solid on for  

2 minutes  

• Ethernet cable x 1  

A WPS connection is established.  

WPS  

Green  

• Telephone cable x 1 (if any)  

• Optical fiber cable x 1 (if any)  

• Quick installation guide x 1  

The WPS negotiation is ongoing.  

Blinking  

Off  

The WPS function is not activated.  

The USB port is connected. No data is being transmitted.  

The USB port is transmitting data.  

Tips  

Solid on  

Blinking  

Off  

This ONT supports wall mounting (two mounting holes on the bottom). The recommended parts are as follows:  

- Expansion bolt: Thread diameter: 6.0 mm; Length: 26.4 mm; Inner diameter: ꢀ2.4  

- Screw: Quantity: 2; Diameter: 3.0-4.0 mm; Head diameter: 5.0-6.5 mm.  

USB  

Green  

The USB port is disconnected.  

Step 2: Set up a WAN connection  

1. Connect and register the ONT  

2. Configure the internet access  

Tips  

For initial registration of the ONT, you can configure the quick registration function according to the page  

prompts. In INTERNET Settings module, you can set the parameters to set up a WAN connection  

according to your ISP and your own needs, and click Apply Changes. If not, refer to the following to set up  

a WAN connection.  

Caution, laser  

Tips  

DO NOT look directly at the PON port when the device is powered on, as well as the terminal of the indoor fiber  

- PPPoE is used for illustration here. Change the parameters as required by your ISP.  

- Choose a desired mode to configure your internet access:  

cord, to prevent any harm to your eyes.  

➊ Choose WAN > PON WAN.  

Router mode: Configure the internet on the ONT.  

➋ Tick Enable VLAN.  

Connect the ONT as shown in the figure. Wait until the PON LED indicator lights solid on, then the ONT is  

Bridge mode: Dial-up on the router or terminal connected to the ONT.  

➌ Enter the VLAN ID provided by your ISP.  

➍ Set Channel Mode to PPPoE.  

registered successfully.  

(Example: HG15)  

➎ Set Connection Type to INTERNET.  

Router mode  

➏ Enter the PPPoE UserName and Password provided by your ISP.  

➐ Set other parameters according to your ISP and your own needs.  

➑ Click Apply Changes.  

Step 1: Log in to the web UI  

➒ Click OK when Change setting successfully is shown on the page.  

Fiber cord  

Tips  

Power adapter  

You can log in to the web UI of the ONT with user permissions or administrator permissions. Administrator  

permissions are for the installation and maintenance personnel only.  

PON WAN  

This page is used to configure the parameters for PONWAN  

•

User Permissions: Able to view and modify partial configurations of the ONT. The default login user  

name is admin. You can get the password from the bottom label on the ONT.  

ppp0_nas0_0  

Enable VLAN:  

•

Administrator Permissions: Able to view and modify all configurations of the ONT. Some  

configurations changed by the installation and maintenance personnel will affect the normal operation  

of the ONT. Therefore, use the administrator permissions with caution. The default login user name and  

password are both admin (or root).  

VLAN ID:  

11  

802.1p_Mark  

Channel Mode:  

Admin Status:  

Connection Type:  

MTU  

1

➋

PON port  

PPPoE  

WPS/RST  

Enable  

Disable  

➊

P

O

N

P

W

R

TEL  

LAN2  

LAN1  

➊ Connect to the ONT.  

INTERNET  

1492  

Rear panel  

Bottom panel  

• Wired device: Connect a LAN port of the ONT to a wired device, such as a computer, using an Ethernet  

cable.  

Enable IGMP-Proxy:  

Enable MLD-Proxy:  

IP Protocol:  

• Wireless device: Connect your wireless device, such as a smartphone, to the Wi-Fi network of the ONT  

using the SSID (Wi-Fi name) and Key (Wi-Fi password) on the bottom label.  

➋ Start a web browser and visit 192.168.1.1.  

IPv4  

Tips  

PPP Settings:  

UserName:  

Password:  

• HG15 is used for illustration here unless otherwise specified. The actual product prevails  

• Press ON/OFF button (if any) to turn on the ONT.  

test  

➌ Enter the User Name and Password according to the actual permissions.  

➍ Click Login.  

11  

• If ISP provides any parameters for registration, you can use them to manually register the ONT with the quick  

registration function. The quick registration function is available only when the ONT is registered for the first time.  

Type:  

Continuous  

Server Name:  

Service Name:  

192.168.1.1  

Method:  

➊ Log in to the web UI of the ONT.  

Port Mapping:  

LAN_1  

Refer to Step 1 in the Router mode of the 2. Configure the internet access.  

LAN_2  

LAN_4  

➋ In GPON Settings (or EPON Settings) module, register with the parameters provided by your ISP and click  

LAN_3  

Apply Changes.  

WLAN0  

WLAN0-AP1  

WLAN0-AP3  

WLAN1  

WLAN0-AP2  

WLAN0-AP4  

User Name:  

Password:  

WLAN1-AP1  

WLAN1-AP3  

WLAN1-AP2  

WLAN1-AP4  

Login  

Reset  

Apply Changes  

Delete  

(Example: HG15)  

Tips  

HG15 is used for illustration here unless otherwise specified. The actual product prevails.  

Tips  

If the above page does not appear, refer to Q1 in FAQ.  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Tenda HG Series xPON ONT Network Router Installation Guide
Make	Tenda
Language	English
Filetype	PDF (Download)
File size	0.22 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL WI-FI INSTRUCTIONS & USER MANUALS
• Tenda

Questions and Answers (0)

If you have any questions regarding Tenda HG Series xPON ONT Network Router Installation Guide, please ask here and describe the problem in detail.