HiKOKI M12V2 Variable Speed Router Instruction Manual
English
As shown in Fig. 12, to install insert template guide in (2) The bit rotates clockwise (arrow direction indicated on
center hole in template guide adapter with 2 accessory
the base). To obtain maximum cutting effectiveness,
feed the router in conformance with the feed directions
shown in Fig. 20.
screws.
A template is a profiling mold made of plywood or
thin lumber. When making a template, pay particular NOTE
attention to the matters described below and illustrated
in Fig. 13.
If a worn bit is used to make deep grooves, a high
pitched cutting noise may be produced.
When using the router along the interior plane of the
template, the dimensions of the finished product will be
Replacing the worn bit with a new one will eliminate the
high pitched noise.
less than the dimensions of the template by an amount
equal to dimension “A”, the difference between the
radius of the template guide and the radius of the bit. The
reverse is true when using the router along the exterior of
the template.
7
Trimmer Guide (Optional accessory) (Fig. 21)
Use the trimmer guide for trimming or chamfering. Attach
the trimmer guide to the bar holder as shown in Fig. 22.
After aligning the roller to the appropriate position,
tighten the two wing bolts (A) and the other two wing
bolts (B). Use as shown in Fig. 23.
(3) Straight guide (Fig. 14)
Use straight guide for chamfering and groove cutting
along the materials side.
MAINTENANCE AND INSPECTION
1. Oiling
Insert the guide bar into the hole in the bar holder, then
lightly tighten the 2 wing bolts (A) on top of the bar
holder.
To ensure smooth vertical movement of the router,
occasionally apply a few drops of machine oil to the
sliding portions of the columns and end bracket.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws be
loose, retighten them immediately. Failure to do so could
result in serious hazard.
Insert the guide bar into the hole in the base, then firmly
tighten the wing bolt (A).
Make minute adjustments of the dimensions between
the bit and the guide surface with the feed screw, then
firmly tighten the 2 wing bolts (A) on top of the bar holder
and the wing bolt (B) that secures the straight guide.
As shown in Fig. 15, securely attach the bottom of the
base to processed surface of the materials. Feed the
router while keeping the guide plane on the surface of
the materials.
3. Maintenance of the motor
The motor unit winding is the very “heart” of the power
tool.
(4) Dust guide and Dust guide adapter (Fig. 16)
Your router is equipped with dust guide and a dust guide
adapter.
Exercise due care to ensure the winding does not
become damaged and/or wet with oil or water.
4. Inspecting the carbon brushes
Match the 2 grooves on the base and insert the 2 dust
guide tabs in holes located in the base side from the top.
Tighten the dust guide with a screw.
For your continued safety and electrical shock protection,
carbon brush inspection and replacement on this tool
should ONLY be performed by a HiKOKI AUTHORIZED
SERVICE CENTER.
The dust guide diverts cutting debris away from the
operator and directs the discharge in
direction.
a
consistent
5. Replacing supply cord
If the supply cord of Tool is damaged, the Tool must be
returned to HiKOKI Authorized Service Center for the
cord to be replaced.
By fitting the dust guide adapter into the dust guide
cutting debris discharge vent, the dust extractor can be
attached.
4. Adjusting the rotation speed
The M12V2 has an electronic control system that allows
stepless rpm changes.
CAUTION
In the operation and maintenance of power tools, the
safety regulations and standards prescribed in each
country must be observed.
As shown in Fig. 17, dial position “1” is for minimum
speed, and position “6” for maximum speed.
5. Removing the spring
The springs within the column of the router can be
removed. Doing so will eliminate spring resistance and
allows easy adjustment of cutting depth when attaching
the router stand.
SELECTING ACCESSORIES
The accessories of this machine are listed on page 121.
For details regarding each bit type, please contact the
HiKOKI Authorized Service Center.
(1) Loosen the 4 sub base screws, and remove the sub
base.
(2) Loosen the stopper bolt and remove it, so the spring can
be removed. (Fig. 18)
CAUTION
GUARANTEE
Remove the stopper bolt with the main unit (router) fixed
at its maximum height.
We guarantee HiKOKI Power Tools in accordance with
statutory/country specific regulation. This guarantee does
not cover defects or damage due to misuse, abuse, or
normal wear and tear. In case of complaint, please send
the Power Tool, undismantled, with the GUARANTEE
CERTIFICATE found at the end of this Handling instruction,
to a HiKOKI Authorized Service Center.
Removing the stopper bolt with the unit in a shortened
condition may cause the stopper bolt and spring to be
discharged and cause injury.
6. Cutting
CAUTION
○
○
Wear eye protection when operating this tool.
Keep your hands, face and other body parts away from
the bits and any other rotating parts, while operating the
tool.
(1) As shown in Fig. 19, remove the bit from the work pieces
and press the switch lever up to the ON position. Do
not start cutting operation until the bit has reached full
rotating speed.
8
| General | Details |
|---|---|
| Name | HiKOKI M12V2 Variable Speed Router Instruction Manual |
| Make | HiKOKI |
| Language | English |
| Filetype | PDF (Download) |
| File size | MB |
(1 votes, average: 5.00 out of 5)
Loading...
If you have any questions regarding HiKOKI M12V2 Variable Speed Router Instruction Manual, please ask here and describe the problem in detail.
HiKOKI M12VE Variable Speed Router Instruction Manual
JUNIPER SSR1300 Session Router User Guide
EE HH10E 4G Hub 2 WiFi Router User Guide
Ruijie Reyee RG-EG105GWT Router User Guide
LINKSYS AX3200 Dual-Band Gigabit Wi-Fi 6 Router User Guide
ASUS AX7800 Tri Band WiFi Router User Guide
RYOBI RTR18 Trim Router Instruction Manual
Cudy LT15E 4G Cat 12 AX3000 Wi-Fi 6 Router Installation Guide
Digital Yacht NeXuX Connect WiFi Router Installation Guide
VIRTUAL ACCESS GW1000M Series Router User Manual
ATEL WB550 5G Fixed Wireless Access Router User Guide