Micronet Union Technology WWYLT18 AC1200 Gigabit Dual Band Wi-Fi Router User Guide

1

③ In the router management interface, click Install-Install Settings  

and select PPPoE. Fill in the User Name and Password, click Save.  

Wait for the device to save the settings and Internet access is  

available. The Wi-Fi name is the default name (on the label at the  

bottom of the device).  

2. Configure the Internet  

1. Schematic Diagram of Router Connection  

2.1. Configure the Router in Bridge Mode  

After the connection is completed, use a mobile phone or computer  

to search for the Wi-Fi name 2.4G SSID or 5G SSID on the label at  

the bottom of the device, enter the password, connect to the Wi-Fi,  

and then the Internet access is available.  

2.2. Configure the Router in Gateway Mode  

2.2.1. Dial-up for Internet Access：  

①After the connection is completed, use a mobile phone or  

computer to search for the Wi-Fi name 2.4G SSID or 5G SSID on  

the label at the bottom of the device and enter the corresponding  

password to connect to Wi-Fi. Open the mobile phone or computer  

browser, visit the 192.168.10.1 website, enter the default username  

and default password on the label at the bottom of the device, and  

enter the router management interface.  

2.2.2. Static IP for Internet Access  

In the router management interface, click Network-Network  

② In the new router management interface, select Network—5G  

Settings—Network Scan, click Site Survey, select the uplink signal,  

click Next.  

User Guide  

Use DSL or PON for Internet connection  

Settings-WAN Connection, select Static IP in WAN Access Type, fill  

in the IP Address, Subnet Mask, Default Gateway and DNS1 (DNS2  

and DNS3 are optional) and click Save&Apply, wait for the device to  

save the settings and Internet access is available. The Wi-Fi name  

is the default name (on the label at the bottom of the device).  

AC1200 Gigabit Dual Band Wi-Fi Router  

Wireless connection  

modem  

The client-side connects to router Wi-Fi  

Connect the Device  

The defaulted username  

and password are on the  

bottom label  

telephone line or fiber  

cable  

Or  

Or  

Connect the PC and router via LAN1, LAN2 or LAN3 with cable  

Wired connection  

② Enter the router management interface and select the network-  

mode. Change the mode to gateway mode.  

Community broadband Internet access  

2.2.3. Dynamic IP for Internet Access  

③ Fill in Pre-Shared Key and click Connect.  

The router is defaulted to dynamic IP (DHCP Client) for Internet  

access. The Wi-Fi name is the default name (on the label at the  

bottom of the device).  

switch on  

Packing list:  

1.The device  

2.User guide  

3.Power adapter  

4.Ethernet cable  

cable  

2.3. Configure the Router in Repeater Mode  

① In the router management interface, select Network-Mode,  

change the mode to Repeater, and click Save&Apply.  

cable  

cable  

If the above accessories are missing, please contact the  

customer service for replacement.  

4.2. Step 2: set up the Agent  

When router’s EasyMesh has been disabled, the device will depart  

from the original EasyMesh network. If to open EasyMesh again,  

please perform step 2 and step 3 to rejoin the network.  

3. Revise Wi-Fi Password  

The Agent needs to be in the Bridge mode in 2.1.  

In the router management interface of other routers (except the  

FCC Warning Statement  

After-sales Service Commitment  

In the router management interface of 192.168.10.1, click Install-  

Install Settings, you can customize the 2.4G and 5G SSID and  

Password.  

router set in the first step), select Network—EasyMesh—General, in  

FCC Radiation Exposure Statement: The antennas used for  

this transmitter must be installed to provide a separation  

distance of at least 20 cm from all persons and must not be  

co-located for operating in conjunction with any other  

antenna or transmitter.  

① Implementation of the three guarantees regulations, seven  

days return, 15 days replacement, one-year warranty;  

the general setting page:  

① Fill in Mesh Agent in Device Name.  

② Select Agent in Role.  

6. Other information  

② The free warranty period of the product is one year,  

calculated from the date of sale;  

③ Click Save & Apply.  

Precautions:  

Changes or modifications not expressly approved by the  

party responsible for compliance could void the user’s  

authority to operate the equipment.  

③ Under the following circumstances, three guarantees are  

not implemented, and paid maintenance is implemented:  

① After completing EasyMesh networking, the Controller device will  

synchronize its 2.4GHz and 5GHz SSID, password, and channel  

with the Agent device. That is, these configurations of the Agent  

device will be the same as the Controller device.  

4.4. EasyMesh networking of three or more devices  

a. Failure caused by man-made damage, improper operation  

or irresistible natural disasters;  

Perform step 2 on the third and more devices.  

This equipment has been tested and found to comply with the  

limits for a Class B digital device, pursuant to Part 15 of the  

FCC Rules. These limits are designed to provide reasonable  

protection against harmful interference in a residential  

installation. This equipment generates uses and can radiate  

radio frequency energy and, if not installed and used in  

accordance with the instructions, may cause harmful  

interference to radio communications. However, there is no  

guarantee that interference will not occur in a particular  

installation. If this equipment does cause harmful  

b. Failure caused by remodeling, disassembling and  

assembling the product by yourself;  

② After modifying the SSID, password, and channel on the  

Controller device, the Controller device will synchronize these  

configurations to all Agent devices. Modifying the SSID and  

password on the Agent device will not be synchronized.  

c. Exceeding the validity period.  

4.3. Step 3: Two devices’ EasyMesh networking  

③ After the device restarts after a power failure, the device will  

restore the EasyMesh network group by default, and no connection  

settings are required.  

After the two devices complete step 1 and step 2, the General  

interface will refresh, and the Start PBC button will appear.  

In the General interface of one of the devices, click the Start PBC  

5. Disable EasyMesh  

④ If the EasyMesh function of the Controller device is disabled, the  

entire EasyMesh network will be disabled.  

button or short press the device's WPS button, and within two  

minutes enter the General interface of the other device, click Start  

PBC button or short press the WPS button of the device to trigger  

automatic network pairing. (Note that long pressing the WPS key is  

rest)  

interference to radio or television reception, which can be  

determined by turning the equipment off and on, the user is  

encouraged to try to correct the interference by one or more  

of the following measures: ‐‐Reorient or relocate the  

After finishing step 2, perform step 3 for EasyMesh networking with  

routers that have been networked.  

In the router management interface, select Network-EasyMesh-  

General, select Disabled in Role, and click Save. Then the  

EasyMesh network can be disabled.  

4. Configure EasyMesh  

⑤ If the EasyMesh function of the Agent device is disabled, the  

device will leave the EasyMesh network.  

4.1. Step 1: set up the Controller  

receiving antenna.  

‐‐Increase the separation between the equipment and  

⑥ If you need to switch the access mode of a certain Mesh device,  

you need to turn off the Mesh function of the device first, and then  

turn on the Mesh function to complete the switching of the access  

mode.  

In the router management interface connected to the upper-level  

gateway (optical modem),select Network—EasyMesh—General, in  

4.5. Check the device information in topology  

receiver.  

‐‐Connect the equipment into an outlet on a circuit different  

In the router management interface of the Controller, select  

Network-EasyMesh-Topology,you can see the device name and IP  

address.  

the general settings page:  

① Fill in Mesh Controller in Device Name.  

② Select Controller in Role.  

③ Click Save & Apply.  

from that to which the receiver is connected.  

‐‐Consult the dealer or an experienced radio/TV  

⑦ The Agent device is not supported to connect to other Mesh  

devices via Wi-Fi and wired at the same time. That is, the Agent  

device can only use one of Wi-Fi and wired to connect to other Mesh  

devices.  

technician for help.  

This device complies with part 15 of the FCC rules. Operation  

is subject to the following two conditions (1) this device may  

not cause harmful interference, and (2) this device must  

accept any interference received, including interference that  

may cause undesired operation.  

Manufacturer: Micronet Union Technology(Chengdu)  

Co., Ltd  

Address: Room 502, Building 5, N.O. 528, Yuefei Road,  

Shibantan Street, Xindu District, Chengdu, Sichuan, China  

quick guide(说明书)  

Technical requirements:(技术要求)  

1. Material:80g double-sided coated paper(材质：80g双铜 双面黑白印刷)  

2. Size:90*150mm(单页尺寸：90*150mm)  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	Micronet Union Technology WWYLT18 AC1200 Gigabit Dual Band Wi-Fi Router User Guide
Make	Micronet Union Technology
Language	English
Filetype	PDF (Download)
File size	0.75 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL WI-FI INSTRUCTIONS & USER MANUALS
• Micronet Union Technology

Questions and Answers (0)

If you have any questions regarding Micronet Union Technology WWYLT18 AC1200 Gigabit Dual Band Wi-Fi Router User Guide, please ask here and describe the problem in detail.