Home > PROSCEND > PROSCEND 850G-6PI 6 Port GbE Managed PoE Switch 5G Cellular Router Installation Guide

PROSCEND 850G-6PI 6 Port GbE Managed PoE Switch 5G Cellular Router Installation Guide

1

LED Indicators

850G-6PI Industrial Ethernet Switch

Quick Installation Guide

LED

Color Description

On: Green PWR/RPS is powered.

PWR/RPS

Version: 1.00

Off

PWR/RPS is not powered.

On: Red

Off

On: Green Ethernet LINK UP.

Alarm for abnormal power status or function.

Normal operation or DIP switch OFF.

Connecting Power

ALM

The 850G-6PI Industrial Ethernet Switch can be powered from three power

supplies (input range 48~57 VDC). Two power inputs on the terminal block

and one Mini-DIN power inlet are on the top panel of the switch. Insert the

positive and negative wires (AWG 12-24) into V+ and V- contacts on the

terminal block respectively and use a flat-head screwdriver to push in and

open the wire clamp.

Blinking:

RJ45 LAN port

Link/Act

Ethernet traffic detected.

Green

Off

Ethernet LINK DOWN.

On: Green Ethernet LINK UP at 1000Mbps.

Ethernet LINK DOWN or LINK UP at

10Mbps/100Mbps.

RJ45 LAN port

Speed

Off

On: Green LINK UP.

Blinking:

You can use either “Terminal Block” or “Mini-DIN” for primary power and

“Terminal Block” for the secondary power source, to be a Redundant

Power Input. Check the polarity while connecting.

UPLINK

PoE

Traffic detected.

Green

Off LINK DOWN.

On: Green PoE PD (Powered Device) connected.

Off

PoE PD (Powered Device) disconnected.

First Power Supply

Speed LED

(Green)

Second Power Supply

Link/Act LED

(Green)

RJ45 Connector Pinouts

The pin assignment of RJ45 connector is shown in the following table.

WARNING

1,2

3,6

4,5

7,8

Description

T/Rx+, T/Rx-

PoE Pinouts

V+

V-

The DC power should be connected to a well-fused power supply.

Alarm Relay and Ground

DIN-rail Mounting

▪

The alarm relay output contacts are shown as ALM next to the DC

terminal block connector as the figure below.

STEP 1: Use the screws to install the DIN-rail kit to attach at the rear side

of the switch.

▪

The alarm relay out is “Normal Open”, and it will be closed when it is

detecting any predefined failure such as power failures.

▪

The relay output with current carrying capacity of 1A @ 24 VDC.

The switch must be properly grounded for optimum system performance.

STEP 2: Hook the unit onto the DIN-rail.

STEP 3: Push the bottom of the unit towards the DIN-rail until it locks in

place.

Ground Connector

DIP Switch Setting

DIP

Function Description

ON: Primary power alarm reporting is enabled.

OFF: Primary power alarm reporting is disabled.

1 (PWR)

ON: Redundant power alarm reporting is enabled.

OFF: Redundant power alarm reporting is disabled.

2 (RPS)

Web Interface: Connect & Login

1. Factory default IP: 192.0.2.1

2. Login with default account and password

Username: root

Reset Button

Password: 2wsx#EDC

Function

Operation

Press the Reset button for 2 seconds

and release.

Press the Reset button for 10 seconds

and release.

NOTE

Reboot

Please scan below QR Code to download online resources.

Download Link:

https://www.proscend.com/en/product/850G-6PI.html

Reset to

factory default

850G-6PI

- 1 -

www.proscend.com

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	PROSCEND 850G-6PI 6 Port GbE Managed PoE Switch 5G Cellular Router Installation Guide
Make	PROSCEND
Language	English
Filetype	PDF (Download)
File size	0.1 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Questions and Answers (0)

If you have any questions regarding PROSCEND 850G-6PI 6 Port GbE Managed PoE Switch 5G Cellular Router Installation Guide, please ask here and describe the problem in detail.