Home > Tradewinds > TradeWinds G720 Wireless Router User Guide
TradeWinds G720 Wireless Router User Guide
FCC Warning Statement
1ꢀProduct introduction
2ꢀLink
Link as instruction below
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment. This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
Link Internet
Link Power
Detailed instructions
OR
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for
help.
Router interface icon
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Pilot lamp
Name
Status
Instructions
Power on
Always on
Power indicator light
uncharged
Always out
Flicker
Wireless router
RF Exposure Statement
Wi-Fi is working
Wi-Fi is not enabled
To maintain compliance with FCC's RF Exposure guidelines, This
equipment should be installed and operated with minimum distance
of 20cm the radiator your body. This device and its antenna(s) must
not be co-located or operation in conjunction with any other antenna
or transmitter.
WiFi indicator light
Always out
Set up work mode
5.FAQs
3ꢀManage Device
4ꢀWireless testing
Enter setup page, click Network-WAN, click apply after choose work mode.
DHCP: Your router IP will be automatically configuredStatic
IP: Your router IP will be fixed as your setup IP.
Solutions
Questions
Log in Web manage page
Use Laptop or mobile phone to test whether the wireless network can surf the
Internet: click wireless network , select the wireless SSID, enter the
Restore the device to default settings, press
and hold theReset button for over 10 s, and
then release the pressing The device will restart
and restore to factory settings.
Forget the login
username and
password
PPPoE: ADSL to connect internet
to connect the wireless AP, test whether you can surf the Internet.
1.Check whether the lP address and the AP are on
thesame segment.Check whether the lP address
ismanually confgured to other segment.
2. Restore the wireless AP to the factory settings,
and tryconnecting again.
Cannot log in to
the wireless
management
pagethrough web
3. Make sure that the lp 192.168.188.253 is not
occupied by other devices.
4. Check the computer of the network cable.
Werecommend using unshielded twisted pair
as thenetwork cable.
1. Connect device with cables, enter the web
management page. Click wireless setting and
basicsetting. Enter the password again in the
secret key.
2. Restore to the factory settings, there is no
password isby default.
Forget the
password of
the wireless
network.
Wi-Fi setup
Enter setup page to set up Wi-Fi. Please note that Wi-Fi password length
at least 8 digits. After set up, please click apply to save settings
Check the status of the wireless network connection: signal quality, speed,
Bytes sent and received. Click on Details, check if the IP address and DNS
server address etc. obtainedcorrectly, confirm that the device is working
properly.
1. Check whether the DHCP server is enabled on
the device.
2. In AP mode, check whether the upper-layer
network connection is normal or whether the
DHCP service on the LAN is enabled.
Cannot acquire
lP address.
It is necessary to transmit on 40MHz channel
bandwidth to reach 300M speed, and the router
and terminal network card must support 40MHZ.
The 2.4G band of the wireless audit route works
at 20MHz channel bandwidth by default. You can
adjust the device configuration on the wireless
service platform and change the channel bandwidth
to 20/40MHz or 40MHz to achieve 300M wireless
transmission rate.
Once the setup
is complete,
the connection is
also successful
but the wireless
display is 150M
instead of 300M.
| General | Details |
|---|---|
| Name | TradeWinds G720 Wireless Router User Guide |
| Make | Tradewinds |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.33 MB |
(1 votes, average: 5.00 out of 5)
Loading...
If you have any questions regarding TradeWinds G720 Wireless Router User Guide, please ask here and describe the problem in detail.
Cudy LT15E 4G Cat 12 AX3000 Wi-Fi 6 Router Installation Guide
altice UBN2309 XGS-PON Labs Delivers Router Instruction Manual
MERCUSYS AC12G Wireless Router Installation Guide
D-Link AX4800 Mesh Wi-Fi 6 Router Installation Guide
UBIQUITI ER-X-SFP Edge Router User Guide
Harvilon MF302 4G LTE Wi-Fi Router User Guide
MIKROTIK 2004-1G-12S+2XS Cloud Core Router User Manual
perle IRG5541+ FirstNet LTE Router User Guide
ZTE MC888 Ultra 5G Router Instruction Manual
LANCOM SYSTEMS 1930EF Gigabit Ethernet Black Wired Router User Guide