Home > wis network > wis network WIS-N300-LTE 4G LTE Router User Guide
wis network WIS-N300-LTE 4G LTE Router User Guide
Package content
Install the radio
1
2
3
Internet via 4G LTE
1.Please insert the available Micro SIM card correctly, Use a network cable to
connect the LAN port to PC.
O E 4G LTE Router
Internet configuration method used as a single router
O
E
4G
L
TE Router
After the router is powered on, the power indicator light is green. After 90 seconds,
the system is successfully started, and the WiFi light is green.
2.Power on the device and login to the device management Web-page.
3. Click on LTE Setting and check that Mobile Dial is enabled.
QuickSetupGuide
4G TE Router
L
Models: WIS-N300-LTE
4G LTE Router
12VꢀDCꢀAdapter
SIM
Interface
LED Interface
Internet
RST
DC--12V
LAN2
LAN1
WAN
SIM
4. Click Dial Up, click New Profile to add APN configuration.
RST
SIM
Please confirm the specific APN configuration with the local operator.
LAN2
LAN1
WAN
DC--12V
W
e
b
c
o
n
fi
g
u
r
a
t
i
o
n
4
1
2
3
5
4
3
2
1
1. Check all wires are correctly connected.
2. Configure the host system dynamic IP to get the IP from the router.
3. Using a web browser access 192.168.1.1 (wait a few seconds after device power up).
4. When login page appears enter “admin” in both the username and password fields.
5. For more configurations settings please visit the support site at www.wisnetworks.com.
LED
Description
No.
1
Description
ꢀDC: Input voltage 12V
Power
On: the radio is powered up
2
WAN: 10/100 Mbps Enternet Port
LAN: 10/100 Mbps Enternet Port
SIM Solt: Micro SIM Card
On:connected to the internet
Internet
Off:not connected to the internet
3
4
On: the WiFi is available
Off: the WiFi is disabled
WLAN
Username :
Password :
Quick Setup Guide
Reset Button:
Press more than 8s to restore
factory settings
5
Since different regions use different LTE Bands, please check with your local operator whether
the supported LTE Bands or frequencies are compatible with Wisnetwork LTE devices.
English
Language :
Login
4G LTE Router
Models: WIS-N300-LTE
ATTENTION
ATTENTION
If you use other PoE Adapter which is not provided by Wisnetworks, we can’t provide warranty
service if device damage caused.
Shielded Category 5 (or above) cabling should be used for all wired Ethernet connections.
Safety Notices
RoHS/WEEE Compliance Statement
Limited Warranty
Internet via WAN PORT
1. Connect the WAN port of the device to the Internet with a network cable, and
1. Read, follow, and keep these instructions.
2. Heed all warnings.
Wisnetworks warrants that the product(s) furnished hereunder (the “Product(s)”) shall be free from
defects in material and workmanship for a period of one(1)ꢀ year from the date of shipment by
Wisnetworks under normal use and operation. Wisnetworks sole and exclusive obligation and liability
under the foregoing warranty shall be for Wisnetworks, at its discretion, to repair or replace any Product
that fails to conform to the above warranty during the above warranty period. The expense of removal
and reinstallation of any Product is not included in this warranty. The warranty period of any repaired or
replaced Product shall not extend beyond its original term.
connect the LAN port of the device to the computer.
3. Only use attachments/accessories specified by the manufacturer.
European Directive 2002/96/EC requires that the equipmentbearing this symbol on the product and/or
its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this
product should be disposed of separately from regular household waste streams. It is your responsibility
to dispose of this and other electric and electronic equipment via designated collection facilities appointed
by the government or local authorities. Correct disposal and recycling will help prevent potential negative
consequences to the environment and human health. For more detailed information about the disposal of
your old equipment, please contact your local authorities, waste disposal service, or the shop where you
purchased the product.
2. Power on the device and login to the device management Web-page.
WARNING:
Do not use this product in location that can be submerged by water.
WARNING:
Avoid using this product during an electrical storm. There may be a
remote risk of electric shock from lightning.
Warranty Condition
The above warranty does not apply if the Product:
Electrical Safety Information
1. Compliance is required with respect to voltage, frequency, and current requirements indicated
on the manufacturer’s label. Connection to a different power source than those specified may result
in improper operation, damage to the equipment or pose a fire hazard if the limitations are not followed.
2. There are no operator serviceable parts inside this equipment. Service should be provided only by
a qualified service technician.
FCC STATEMENT
3. Click WAN Setting, click Edit to configure the WAN port parameters.
(a) has been modified and/or altered, or an addition made thereto, except by Wisnetworks, or our
authorized representatives, or as approved by Wisnetworks in writing;
(b) has been painted, rebranded or physically modified in any way;
(The default is DHCP)
1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(c) has been damaged due to errors or defects in cabling;
(2) This device must accept any interference received, including interference that may cause undesired
operation.
(d) has been subjected to misuse, abuse, negligence, abnormal physical, electromagnetic or electrical
stress, including lightning strikes, or accident;
3. This equipment is provided with a detachable power cord which has an integral safety ground wire
intended for connection to a grounded safety outlet.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
(e) has been damaged or impaired as a result of using third party firmware;
(f) has no original Wisnetworks MAC/SN label, or is missing any other original Wisnetworks label(s);
(g) human reasons without according to the guide or user manual.
a. Do not substitute the power cord with one that is not the provided approved type. Never
use an adapter plug to connect to a 2-wire outlet as this will defeat the continuity of the
grounding wire.
NOTE: This equipment has been tested and found to comply withthe limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
b. The equipment requires the use of the ground wire as a part of the safety certification,
modification or misuse can provide a shock hazard that can result in serious injury or death.
c. Contact a qualified electrician or the manufacturer if there are questions about the installation
prior to connecting the equipment.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can bedetermined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
In addition, the above warranty shall apply only if: the product has been properly installed and used at
all times in accordance, and in all material respects, with the applicable Product documentation; all
Ethernet cabling runs use CAT5 (or above), and for outdoor installations, shielded Ethernet cabling is
used, and for indoor installations, indoor cabling requirements are followed.
d. Protective earthing is provided by Listed AC adapter. Building installation shall provide
appropriate short-circuit backup protection.
e. Protective bonding must be installed in accordance with local national wiring rules and
regulations.
Increase the separation between the equipment and receiver.
Online Support
Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Marking
For more guide and help, please go to
This equipment complies with FCC radiation exposure limitsset forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
CE marking on this product represents the product is in compliance with all directives that are applicable
to it. Alert sign must be indicated if a restrictionon use applied to the product and it must follow the CE
marking.
You can contact email
We’ll reply you within one weekday.
Scan for more product information
4. For more configurations like operating mode and wireless settings please visit the support
site at www.wisnetworks.com.
| General | Details |
|---|---|
| Name | wis network WIS-N300-LTE 4G LTE Router User Guide |
| Make | wis network |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.8 MB |
(1 votes, average: 5.00 out of 5)
Loading...
If you have any questions regarding wis network WIS-N300-LTE 4G LTE Router User Guide, please ask here and describe the problem in detail.
wis network 5G CPE Pro -Home Router User Guide
wis network WIS-AX3000 WiFi 6 Gigabit PoE Router User Guide
ASUS U18086 ROG GT-AXE11000 Wireless Router User Guide
KuWFi CF5 4G LTE CPE Router User Manual
TCL LINKHUB HH40L2 Wi-Fi Router User Manual
ReadyNet AX1500M WiFi6 Wireless Router User Guide
Antena Gear TX54 5G Cellular Router User Guide
TP-Link 7106511948 Outdoor Router Installation Guide
Cudy LT500 4G LTE AC1200 Dual Band WiFi Router User Guide
EDIMAX BR-6428NS V5 4 in 1 N300 WiFi Router Installation Guide
TP-Link Archer MR200 Wireless Dual Band 4G LTE Router User Guide
Keep Your Home IP MA-B256 Router Owner’s Manual