FESTOOL OF 1010 REBQ Electric Handheld Router Instructions

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

96

97

98

99

100

101

102

103

104

105

106

English  

7.8 Dust extraction  

8.2 Routing with a parallel side fence  

For work running parallel to the workpiece  

edge, the supplied parallel side fence [6-4] can  

be used.  

WARNING  

Heath hazard posed by dust  

► Always work with an extractor.  

► Comply with national regulations.  

WARNING  

Risk of injury  

CAUTION! If an anti-static suction hose is not  

used, static charge may occur. The user may  

receive an electric shock and the electronics of  

the power tool may be damaged.  

A Festool dust extractor with an extractor hose  

diameter of 36 mm or 27 mm (36 mm recom-  

mended due to the reduced risk of clogging)  

can be connected to the extractor connec-  

tor [1-15].  

Upon installation on the wrong side, the  

router may touch the parallel side fence.  

► Only install the parallel side fence on the  

side of the power tool depicted in the im-  

age [6].  

► Clamp the two guide rods [6-7] to the paral-  

lel side fence using the two rotary  

knobs [6-2].  

► Insert the guide rods into the grooves of the  

router table to the required extent and  

clamp them using the rotary knob [6-3].  

This distance can be adjusted faster and more  

precisely with the fine precision adjust-  

ment [6-6] available as an accessory:  

Chip catcher KSF-OF  

KSF-OF chip catcher [3-1] (partly accessory)  

consists of a hood and cover and can increase  

the efficiency ot the extraction when routing  

edges. Installation is similar to that of the copy-  

ing ring., the cover is attached at the top.  

► Turn the adjusting screw [6-5] in the plastic  

part of the guide.  

► Clamp the guide rods with the rotating  

knobs [6-1] in the precision adjustment.  

► Loosen the rotating knobs [6-2] of the par-  

allel guide.  

The hood can be cut off along the grooves [3-2]  

using a hacksaw and can thus be reduced in  

size. The chip catcher can then be used for inte-  

rior radiuses up to a minimum radius of 40 mm.  

8

Working with the electric  

power tool  

► Set the desired distance with the adjusting  

screw and retighten the rotating knobs.  

When working on the machine, observe  

all of the safety warnings that are listed  

at the start as well as the following rules:  

For better extraxtion, a special suction  

hood is available as an accessory for the  

side stop.  

–

–

–

Only guide the power tool towards the  

workpiece when it is switched on.  

Always secure the workpiece in such a way  

that it cannot move during machining.  

When working, always hold the power tool  

with both hands on the handles [1-7] +  

[1-13]. This is a prerequisite for precise  

work and is essential for plunge-cutting.  

Plunge into the workpiece slowly and even-  

ly.  

When routing, ensure that the power tool's  

feed direction is the same as the tool's cut-  

ting direction, see figure [5].  

8.3 Routing with the FS guide system  

The guide system (available as an accessory)  

makes it easier to route straight grooves.  

► Secure the guide rail adapter [7-4] to the  

router table using the guide rods [7-3] of  

the parallel side fence.  

► Secure the guide rail [7-6] to the workpiece  

using fastening clamps [7-7].  

Ensure that there is a safety distance X of  

(see figure [7]) 5 mm between the front  

edge of the guide rail and the cutter, or the  

groove.  

–

► Place the guide rail adapter on the guide  

rail, as shown in figure [7]. To ensure that  

the router stop can be guided without play,  

use a screwdriver through the top open-  

ings [7-5] on the side to adjust the two  

guidance jaws.  

8.1 Freehand routing  

Freehand routing is the method normally used  

for lettering or shapes, and for routing edges  

using cutters with a guide pin or ring.  

► Tighten the height-adjustable support [7-2]  

on the threaded hole of the router table so  

19  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	FESTOOL OF 1010 REBQ Electric Handheld Router Instructions
Make	FESTOOL
Language	English
Filetype	PDF (Download)
File size	2.81 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL WI-FI INSTRUCTIONS & USER MANUALS
• FESTOOL

Questions and Answers (0)

If you have any questions regarding FESTOOL OF 1010 REBQ Electric Handheld Router Instructions, please ask here and describe the problem in detail.