SERCOMM IP5446M WiFi Router User Guide
Appendix A
Regulatory
Setup the IP5446M
Step 6: Choose the Basicpage, click WAN Setup, to con�igure your WAN settings.
Setting up the IP5446M is simple. Power up the IP5446M with the provided
power supply and connect the WAN port (Blue) to your modem with a standard
Ethernet cable. By default, the IP5446M uses the pre-con�igured WiFi SSID and
password match what is shown on your WiFi Credential Card and the label.
FCC Statement
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one of the
following measures:
If you have �iber service at home, the unit will be ready to use without any
additional con�iguration. If you have another type of Internet service, follow the
instructions shown below to change the WAN setting to DHCP.
If you would like to set a custom WiFi SSID and password, you can also use the
IP5446Mlocal web page and follow the steps below.
Setup Using Web Browser
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
To assure continued compliance, any changes or modi�ications not
expressly approved by the party responsible for compliance could void the
user's authority to operate this equipment. (Example - use only shielded
interface cables when connecting to computer or peripheral devices).
Chapter 3
Safety
Step 8: To change the WiFi SSID and password, select the Wireless page, click
Basic Setup, then go to the Setup menu and change the SSID and password. When
you are �inished, click Apply to save your changes.
This chapter provides you some safety operation warnings.
FCC Radiation Exposure Statement
Step 1: Make sure yourmodem is on and working properly.
This equipment complies with FCC RF radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 2 centimeters between the radiator
and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
1. Use the power supply adapter provided in the package only. Using any other
Step 2:Connect the IP5446M WAN port (Blue) with your modem with a standard
Ethernet cable.
adapters may cause damage to the equipment or result in operation failures.
Step 7: The default Connection Type is PPPoE for Internet service over �iber. For
other type of services, select DHCP and click Apply.
Step 3: Connect an Ethernet cable to anIP5446M LAN port and your PC.
2. The electrical load capacity of the socket and cables should meet the device’s
requirement. Power socket overload, broken cables or broken plugs may
cause electric shock or �ire. Check the power supply wires and cables
regularly.
Step 5:You will be prompted for a username and password. Locate the included
IP5446M Credential Card. Use admin for the default username. The device
speci�ic password can be found by scanning the QR code on the included WiFi
Credential Card or on the IP5446M label (shown as the WPS PIN). The password
can be changed after device setup.
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
3. Install the equipment in a well-ventilated environment. Avoid areas with high
temperature or direct sunlight to protect the equipment and its components
from overheating.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the
US/CANADA
4. Do not place this equipment in a dram or moist place.
Operation of this device is restricted to indoor use only
5. Do not lay this equipment on an unsteady base.
957DQD0001
4
5
6
7
8
| General | Details |
|---|---|
| Name | SERCOMM IP5446M WiFi Router User Guide |
| Make | Sercomm |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.24 MB |
(1 votes, average: 5.00 out of 5)
Loading...
If you have any questions regarding SERCOMM IP5446M WiFi Router User Guide, please ask here and describe the problem in detail.
SERCOMM RP582B Router or Extender User Manual
NETGEAR AXE7800 Tri-Band WiFi 6E Router User Manual
FRITZ 4690 Box Wi-Fi Router User Guide
EE HH10E 4G Hub 2 WiFi Router User Guide
REGIN M4G951 Router Instructions
MOFI NETWORK MOFI6500 4G LTE Router User Manual
QiXiang QX520 Dual SIM Router User Guide
Milesight UR32S CCTV Router Owner’s Manual
JUNIPer SSR120 Session Router User Guide
ELPRO 645M-4 Cellular and WiFi IIoT Router Installation Guide
WM Systems M2M LTE Cat.4 Router Installation Guide