LANCOM Systems 1780EW-4G+ High Performance Mobile VPN Router User Guide

1

➂

➀

➀

➂

➁

Hardware  

LANCOM 1780EW-4G+  

Power supply  

12 V DC, external power adapter 230 V with bayonet connector to secure against  

disconnection  

Power  

consumption  

Approx. 13 W via external power adapter (value refers to the overall power for the  

router and power adapter); about 14 W via PoE (IEEE 802.3at)  

Environment  

Temperature range 0–35 °C; humidity 0–95 %, non-condensing.  

Temperature range 0–40 °C when mounted vertically on a LANCOM wall mount with  

cables running to the side.  

➀

➁

➂

➃

➄

➅

Housing  

Robust synthetic housing, rear connectors, ready for wall mounting,Kensington lock;  

measures 210 x 45 x 140 mm (W x H x D)  

Number of fans  

None; fanless design, no rotating parts, high MTBF  

➂ 4G  

➀ Power  

➃

➄

➅

➆

➇

Interfaces  

Off  

Cellular interface disabled  

Off  

Device switched off  

WAN, LAN  

10 / 100 / 1000 Base-TX, autosensing, auto node hub  

Green,permanently Connection to cellular network active  

Green, permanently Device operational,  

Serial Interface  

Serial configuration interface / COM port (8-pin Mini-DIN): 9,600–115,000 baud,  

suitable for optional connection of analog/GPRS modems. Supports internal COM-port  

server and provides transparent asynchronous serial-data transfer via TCP.  

resp. device paired / claimed and  

LANCOM Management Cloud (LMC)  

accessible  

Green, flickering  

Cellular data transmission  

Orange,  

permanently  

Logon to cellular network successful  

Hardware Quick Reference  

LTE / 4G antennas  

Connect the two supplied cellular antennas to the  

connectors located at the device‘s sides.  

Serial interface  

➀

➁

➂

➄

WLAN: Ant 1, Ant 2 Two reverse SMA connectors for external LANCOM AirLancer antennas or for anten-  

nas from other vendors**  

Configuring the device via the serial interface requires  

a serial configuration cable  

(available as an accessory).  

Green / orange,  

blinking  

Configuration password not set.  

Without a configuration password,  

the configuration data in the device  

is unprotected.  

Orange, blinking  

Red, permanently  

Logging on to cellular network  

4G: Ant 1, Ant 2  

Two SMA connectors for the supplied dipole rod antennas (LTE, UMTS), compatible  

LANCOM AirLancer Extender antennas for 4G or 3G, or from other manufacturers**  

Hardware error/module unavailable  

LANCOM 1780EW-4G+  

GPS antenna (optional)  

Connect the GPS antenna (free of charge) to the  

connector GPS (see included voucher).  

Red / green, blinking SIM card error (PIN)  

1x green inverse  

blinking*  

Connection to the LMC active,  

pairing OK, device not claimed  

GPS  

SMA jack for connecting an optionally available GPS antenna  

WAN interface  

Use the cable with the green-colored connectors to  

connect the interface ETH2 to your WAN modem.  

➅

➆

Red / orange,  

blinking  

Uploading module firmware  

WAN protocols  

Ethernet  

2x green inverse  

blinking*  

Pairing error, resp.  

LMC activation code not available  

➃ SIGNAL  

PPPoE, Multi-PPPoE, ML-PPP, GRE, EoGRE, PPTP (PAC or PNS), L2TPv2 (LAC or LNS)  

and IPoE (with or without DHCP), RIP-1, RIP-2, VLAN, IPv6 over PPP (IPv6 and IPv4 /  

IPv6 Dual Stack Session), IP(v6)oE (Autoconfiguration, DHCPv6 or static)  

WLAN antennas  

3x green inverse  

blinking*  

LMC not accessible, resp.  

communication error  

Off  

No cellular reception  

Screw the two supplied WLAN antennas onto the  

connectors WLAN Ant 1 and WLAN Ant 2. The desired  

MIMO behaviour can be configured under  

Ethernet interface  

Use the cable with the kiwi-colored connectors to  

connect the interface ETH1 (PoE) to your PC or a LAN  

switch.  

Green, permanently Good signal strength,  

greater than or equal to -70 dB  

Data transmission in cellular networks  

➁ WLAN  

> Physical WLAN Settings > Radio > Antenna grouping  

Orange,  

permanently  

Medium signal strength,  

field strength between -86 dB and  

-71 dB  

Supported  

standards  

UMTS, HSxPA, HSPA+, LTE, LTE Advanced  

Off  

No Wi-Fi network defined or Wi-Fi  

module deactivated. The Wi-Fi  

module is not transmitting beacons.  

Optional: SIM card  

➇

Supported cellular Band 1 (2100 MHz), band 2 (1900 MHz), band 3 (1800 MHz), band 4 (2100 MHz),  

Slide the SIM card into the slot using the marker to  

ensure that the card is the right way round. Ensure  

that the SIM card clicks into place on insertion. To  

remove the card from the device again, press the card  

lightly into the device. Let go to release the SIM card  

from the slot.  

Orange, blinking  

Low signal strength,  

field strength less than -87 dB  

network bands  

band 5 (800 MHz), band 7 (2600 MHz), band 8 (900 MHz), band 12 (700 MHz),  

band 13 (700 MHz), band 20 (800 MHz), band 25 (1900 MHz), band 26 (800 MHz),  

band 29 (700 MHz), band 30 (2300 MHz), band 41 (2500 MHz)  

Green, permanently At least one Wi-Fi network is defined  

and Wi-Fi module activated. The  

Wi-Fi module is transmitting  

Power  

➃

➄ ETH  

When connecting the cable to the device, turn the  

bayonet connector 90° clockwise until it clicks into place.  

Use only the supplied power adapter.  

beacons.  

Max. transmission +23 dBm  

power  

Off  

No networking device attached  

Green, inverse  

flashing  

Number of flashes = number of  

connected Wi-Fi stations and P2P  

wireless connections, followed by a  

pause (default).  

Green, permanently Connection to network device  

operational, no data traffic  

GPS  

Positioning with the additional GPS antenna (optional)  

Package content  

Green, flickering  

Data transmission  

Alternatively the frequency of the  

flashing can indicate signal strength  

over the defined P2P link or the  

signal strength between the access  

point and the device operating in  

client mode.  

Cables  

2 Ethernet cables, 3 m (LAN: kiwi-colored connectors; WAN: green connectors)  

➅ VPN  

Antennas  

Power adapter  

Two 3dBi dipole dualband antennas; two LTE / 4G antennas for LTE / UMTS  

Off  

VPN connection inactive  

External power supply adapter 230 V, 12 V / 1.5 A DC/S, barrel connector 2.1 / 5.5 mm  

bayonet, LANCOM item no. 111301 (EU, 230 V), LANCOM item no. 111302 (UK, 230 V)  

Green, permanently VPN connection active  

Green, blinking Establishing VPN connections  

Green, blinking  

Red, blinking  

DFS scanning or other scan  

procedure  

Before initial startup, please make sure to take notice of the information regarding the intend-  

ed use in the enclosed installation guide!  

Please observe the following when setting up the device  

Hardware error in Wi-Fi module  

→ The power plug of the device must be freely accessible.  

→ For devices to be operated on the desktop, please attach the adhesive rubber footpads  

→ Do not rest any objects on top of the device  

Operate the device only with a professionally installed power supply at a nearby power socket  

that is freely accessible at all times.  

i

*) The additional power LED statuses are displayed in 5-seconds rotation if the device is configured to be managed by the LANCOM Manage-  

ment Cloud.  

Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in compliance  

with Directives 2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006.  

The full text of the EU Declaration of Conformity is available at the following Internet address: www.lancom-systems.com/doc  

→ Keep all ventilation slots on the side of the device clear of obstruction  

→ In case of wall mounting, use the drilling template as supplied  

The SIM card may only be inserted or removed when the device is switched off. Inserting or  

removing the SIM card when the device is switched on can destroy the 4G module!  

This product contains separate open-source software components which are subject to their own licenses, in particular the General Public  

License (GPL). The license information for the device firmware (LCOS) is available on the device‘s WEBconfig interface under “Extras > License  

information“. If the respective license demands, the source files for the corresponding software components will be made available on a down-  

load server upon request.  

→ Rack installation with the optional LANCOM Rack Mount (separately available)  

→ In the case of separately purchased antennas, ensure that the permissible transmission power of the system  

is not exceeded. The operator of the system is responsible for compliance with the limits.  

Antennas may only be mounted or replaced when the device is switched off.  

Mounting or removing the antennas when the device is switched on can destroy the 4G or  

Wi-Fi modules!  

**) Please respect the restrictions which apply in your country when setting up an antenna system (in particular the antenna  

gain and transmission power). For information about calculating the correct antenna setup, please refer to  

www.lancom-systems.com.  

Cloud-ready  

VIEW FULL SCREEN PDF MANUAL

General	Details
Name	LANCOM Systems 1780EW-4G+ High Performance Mobile VPN Router User Guide
Make	LANCOM SYSTEMS
Language	English
Filetype	PDF (Download)
File size	0.09 MB

Download PDF

(1 votes, average: 5.00 out of 5)

Loading...

• ALL WI-FI INSTRUCTIONS & USER MANUALS
• LANCOM SYSTEMS

Questions and Answers (0)

If you have any questions regarding LANCOM Systems 1780EW-4G+ High Performance Mobile VPN Router User Guide, please ask here and describe the problem in detail.