Home > LANCOM SYSTEMS > LANCOM SYSTEMS LANCOM OAP-830 Wireless Router User Guide
LANCOM SYSTEMS LANCOM OAP-830 Wireless Router User Guide
Hardware
Mounting
Power supply
Via Power-over-Ethernet compliant to IEEE 802.3af
Power consumption PoE: 12.95 W (measured at the OAP)
Environment
Housing
-33 °C to +70 °C
Robust metal housing, protection class IP 66, for wall and pole mounting.
Note: For installation in salt water environments please use a suitable outer housing.
Dimensions 255 × 250 × 80 mm (length x width x depth)
Power
ETH1
ETH2
a Power
Wi-Fi
ETH 2
(10/100)
ETH 1
(10/100/1000)
ETH 2
(10/100)
ETH 1
(10/100/1000)
WLAN1
WLAN2
Reset
ETH1
WLAN1
WLAN2
Reset
b
c
ETH2
Frequency bands
2.4 GHz and 5 GHz, 2400-2483.5 MHz (ISM) and 5150-5825 MHz
(restrictions vary between countries)
f
Antenna gain
Up to 11dBi at 2.4 and 5 Ghz
a
b
c
d
d
e
Minimum transmission Transmission-power reduction in software by 1 dB steps to min. 0.5 dBm
power
Radio channels
2.4 GHz
Up to 13 channels, max. 3 non-overlapping (2.4-GHz band)
Screw the connector flange b to the back of the housing with the
four screws and their washers.
a Power
b ETH 1 / ETH 2
Radio channels
5 GHz
Up to 26 non-overlapping channels (channels available vary according to country regulations;
DFS for automatic dynamic channel selection required)
Off
Device switched off
Device operational,
resp. device paired / claimed and LANCOM
Management Cloud (LMC) accessible
Off
No networking device attached
ETH 1, ETH 2 interfaces
d
Green, permanently*
Green,
permanently
Connection to network device operational,
no data traffic
When fastening the clamp profile c, please pay attention
to tighten the screws equally with a maximum torque of
7 Nm!
The ETH 1 connector also supplies power to the device. Plug in the water-proof power cable to the ETH 1 port and
carefully tighten the threaded connector. Connect the other end of the network cable to the ‚Power Out‘ connec-
tor i of the supplied PoE injector. Connect the interface ETH 2 with a sealed Ethernet cable to your PC or a LAN
switch.
Interfaces
ETH 1
10 / 100 / 1000 Mbps auto-sensing, PoE as per IEEE 802.3af
Green, flickering
Data traffic
ETH 2
10 / 100 Mbps, preconfigured LAN port, re-configurable to WAN port
Green, blinking
Configuration password not set. Without a
configuration password, the configuration
data in the device is unprotected.
c WLAN1 / WLAN2
Declaration of conformity
Off
No Wi-Fi network defined or Wi-Fi module
deactivated. The Wi-Fi module is not trans-
mitting beacons.
Wall mounting
Pole mounting
Hereby, LANCOM Systems GmbH | Adenauerstrasse 20/B2 | D-52146 Wuerselen, declares that this device is in
compliance with Directives 2014/30/EU, 2014/53/EU, 2014/35/EU, 2011/65/EU, and Regulation (EC) No. 1907/2006.
The full text of the EU Declaration of Conformity is available at the following Internet address:
Reset button (part of the LED block)
To restore the device to its default configuration, keep the reset button on the device pressed until the LEDs on the
device go out. The following automatic restart restores the default configuration to the device.
e
f
1x green inverse
blinking*
Connection to the LMC active, pairing OK,
device not claimed
Use the mounting arm a as a
template. Fix the mounting arm
to the wall with the supplied
screws and dowling plugs.
Place the clamp profile c
around the pole. Screw
the clamp profile onto the
mounting arm with the
supplied screws.
Green
At least one Wi-Fi network is defined and
Wi-Fi module activated. The Wi-Fi module is
transmitting beacons.
2x green inverse
blinking*
Pairing error, resp.
LMC activation code not available
Package content
Grounding
Screw one end of the green/yellow grounding wire to the housing and attach the other end to a suitable ground.
3x green inverse
blinking*
LMC not accessible, resp.
communication error
LANCOM OAP-830
Quick Reference Guide
Cables
Water-resistant, UV-resistant Ethernet cable with screw connector, 15 m
Quick Reference Guide (DE/EN), Installation Guide (DE/EN)
Equipment for wall and pole mounting, screws included
Ensures that the unit remains sealed in case an Ethernet port is unused
Gigabit Ethernet PoE injector (IEEE 802.3af)
Green, flashing
inverse
Number of flashes = number of connected
Wi-Fi stations and P2P wireless connections,
followed by a pause (default).
Alternatively the frequency of the flashing
can indicate signal strength over the defined
P2P link or the signal strength between the
access point and the device operating in
client mode.
Attach the access point with
the connector flange b to the
mounting arm a. Use the
M8 x 110 bolt with spring locking
washer, washer and nut.
Documentation
Mounting kit
Covering cap
PoE injector
Grounding cable
PoE injector - h LAN-In / i Power-Out / g Power supply interfaces
g
h
i
Using Ethernet cables, connect the ‚LAN-In‘ interface h of the provided PoE injector to a free socket of your local
network and the ‚Power-Out‘ interface i to the ETH 1 interface of the access point.
Supply power to the PoE injector g. Only use the supplied PoE Injector to supply power to this device. Particularly,
do not connect the PoE Injector to non-PoE Ethernet devices!
To avoid electrostatic charge
ቪ
ቩ
Green, blinking
Red, blinking
DFS scanning or other scan procedure
Hardware error in Wi-Fi module
ቨ
The main beam direction of the integrated antenna can be adjusted
by tilting the access point up or down by rotating the connection
flange about the mounting arm.
Cloud-ready
Please observe the following when setting up the device
A The housing of the device may become warm during operation.
A If the device is operated with outside temperatures exceeding
60 °C, it should be mounted with protection against contact.
A When operating both Wi-Fi modules in the same frequency band,
mutual interference cannot be ruled out.
Installing access points and/or external an-
tennas without adequate lightning protection
can lead to serious damage to the devices
and/or to the related network infrastructure.
5
*) The additional power LED statuses are displayed in 5-seconds
rotation if the device is configured to be managed by the LANCOM
Management Cloud.
Before initial startup, please make sure to take notice of the information regarding the intended use in the enclosed installation guide!
Operate the device only with a professionally installed power supply at a nearby power socket that is freely accessible at all times.
| General | Details |
|---|---|
| Name | LANCOM SYSTEMS LANCOM OAP-830 Wireless Router User Guide |
| Make | LANCOM SYSTEMS |
| Language | English |
| Filetype | PDF (Download) |
| File size | 0.27 MB |
(1 votes, average: 5.00 out of 5)
Loading...
If you have any questions regarding LANCOM SYSTEMS LANCOM OAP-830 Wireless Router User Guide, please ask here and describe the problem in detail.
LANCOM SYSTEMS 1800EF-4G High Availability Networking Via Fiber Router Owner’s Manual
LANCOM SYSTEMS 1930EF Gigabit Ethernet Black Wired Router User Guide
LANCOM SYSTEMS 1790-4G+ High-Performance VPN Router Installation Guide
LANCOM SYSTEMS 1790VAW GmbH Performance Router User Guide
LANCOM SYSTEMS 1800EFW-5G Router Installation Guide
LANCOM Systems 1780EW-4G+ High Performance Mobile VPN Router User Guide
LANCOM Systems 1793VA VDSL Voip VPN Router User Guide
LANCOM SYSTEMS IAP-4G Plus LTE 4G Router User Guide
LANCOM SYSTEMS LANCOM 1790-4G Plus High-Performance VPN Router Instruction Manual
LANCOM SYSTEMS VPN 1900EF Router Instruction Manual
TCL HH515L Odnowiony Router User Guide
SKYWORTH GN543V GPON ONT WiFi Router Installation Guide
TELTONIKA Networks QSG RUT951 Wi-Fi Dual SIM Router Instruction Manual
Isage VU202R Portable Small Wireless Router Instructions
NETGEAR RS280S Nighthawk WiFi 7 Tri-Band Router Owner’s Manual
Siretta UPnP NAT-PMP Router Instructions
mine media M4 4g LTE Bonding Router User Manual
ZTE MF296C WiFi Router User Manual
CNCU FC300 Easy Route CNC Router Instructions
mobile beacon FX 2000 5G Router User Guide