FLEX FX4221 24V Trim Router Instruction Manual
GENERAL OPERATIONS WITH THE TRIM
ROUTER
Fig. 20
Fig. 21
Fig. 22
Fence
Making test cuts is essential with most routing
applications. A test cut yields information
about the set-up, the speed of the tool, the
cutting depth, and how the cutter bit reacts to
the workpiece. Much of routing is a trial-and-
error process of making various adjustments,
followed by test cuts, while learning all of the
tool’s operational abilities. To avoid ruining good
material, make test cuts on scrap material.
Arm
Knob
When operating the tool, always hold it firmly
with both hands to maintain proper control.
ROUTING WITH THE EDGE GUIDE
BRUSHLESS
The edge guide can be used as an aid in
routing applications such as decorative edging,
straight-edge planning and trimming, grooving,
dadoing, and slotting.
Edge Guide
Assembly
Straight Routing (Fig. 20, 21, and 22)
1. Loosen the knob and slide the fence along
the arm of the edge guide. Once the desired
length is reached, tighten the knob (Fig. 20).
2. With the cutting depth set, place the tool on the
edge of the workpiece, making sure that the
cutter does not contact the workpiece (Fig. 21).
3. Turn the tool ON and allow it to reach its full
speed.
4. To begin the cut, gradually feed the cutter bit
into the edge of the workpiece.
BRUSHLESS
5. Move the tool while keeping the edge guide
flush with the side of the workpiece.
6. When the cut is complete, turn the tool OFF
and allow the cutter bit to come to a complete
stop before removing it from the workpiece.
Guide
7. Remove the battery, place the tool upside-
down on the worktable, and inspect the
finished cut.
Removing the cutter bit
from the workpiece while
WARNING
it is still rotating could damage the
NOTE: Roundover bits with bearings are
excellent for shaping the edge of any workpiece
that is either straight or curved, if the curvature
is at least as great as the radius of the bit to be
used.
workpiece and result in loss of control,
causing possibly serious personal injury.
NOTE: If the distance between the side of
the workpiece and the cutting position is too
wide for the edge guide, or if the side of the
workpiece is not straight, firmly clamp a straight
board to the workpiece and use it as a guide
against the router base. Feed the tool in the
direction of the arrow (Fig. 22).
Always clamp the
WARNING
workpiece securely and
keep a firm grip on the tool base with both
hands at all times. Failure to do so could result
in loss of control, causing possibly serious
personal injury.
-20-
| General | Details |
|---|---|
| Name | FLEX FX4221 24V Trim Router Instruction Manual |
| Make | FLEX |
| Language | English |
| Filetype | PDF (Download) |
| File size | 2.88 MB |
(1 votes, average: 5.00 out of 5)
Loading...
If you have any questions regarding FLEX FX4221 24V Trim Router Instruction Manual, please ask here and describe the problem in detail.
inseego FX3100-1 Wavemaker 5G Router User Guide
3onedata IRT5300L-5T2D-2P12_36 4G Wireless Router Installation Guide
MERCUSYS MB110-4G LTE Router User Guide
MikroTik C52iG-5HaxD2HaxD-TC Wireless Router User Guide
Cisco RV260P Router User Guide
TP-Link Archer VR600 Wireless DSL Modem Router Installation Guide
Taiko Audio V16.x22069 Extreme Router User Manual
TP-Link Omada Pro Gigabit VPN Router Owner’s Manual
Trueview T18168-AE Wireless Router 4G 5G Mobile Sim Based Router User Guide
Cudy WR1300 AC1200 Gigabit Dual Band Wi-Fi Router Installation Guide