TRENDNET AX1800 Dual Band Wifi 6 Gigabit Dual Wan VPN SMB Router User Guide

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

41

42

43

44

45

46

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

96

97

98

99

100

101

102

103

104

105

106

107

108

109

110

111

112

TEW-929DRU  

TRENDnet User’s Guide  

Below is a reference of the additional LAN settings if you choose to make other  

configuration changes to these sections.  

•

Override MTU – The default MTU (maximum transfer unit) or frame size is set  

to 1500 bytes. This parameter allows you to assign a new MTU size. Typically,  

this parameter does not need to be modified.  

General Setup  

•

Status – LAN Interface (br-lan)  

o

Configure LAN IPv4 DHCP server settings  

Network > LAN  

Uptime – Displays the amount time the LAN interface has been up and  

continuously running. This time will reset if the router is powered off  

or router is rebooted.  

Note: The internal DHCP server function is enabled by default on the LAN interface to  

automatically distribute IP address settings to network devices connected to the LAN and  

wireless LAN interfaces. The internal DHCP server only supports only class C IP address  

range. The default IP range is 101 – 199 (192.168.10.101 – 192.168.10.199)  

o

o

o

MAC-Address – Displays the current MAC address assigned to the LAN  

interface.  

Rx – Displays the total amount of data received by the LAN interface in  

MB (# of packets) since the start of the currently displayed uptime.  

Tx – Displays the total amount of data transmitted by the LAN  

interface in MB (# of packets) since the start of the currently displayed  

uptime.  

1. Log into your router management page (see “Access your router management page”  

on page 6).  

o

IPv4: Displays the current IPv4 address settings assigned to the LAN  

interface.  

Mode – Allows you to change the function between NAT mode or Route Only  

2. Click on Network and click LAN.  

•

(NAT-less).  

3. Under the DHCP Server/Relay section, you can modify or enter the new DHCP settings  

and click Apply to save and commit the changes.  

o

NAT – The default router mode which uses network address  

translation between the local internal (LAN/VLAN) interfaces and  

external (WAN1/WAN2) interfaces translating public and private IP  

addressing.  

o

Route Only (NAT-less) – This mode disables the NAT function between  

internal and external interfaces and may also be known as classical  

routing mode. This mode should only be used when the router is using  

for local internal IP routing only  

Advanced Settings  

•

Override MAC Address – This parameter allows you to assign a new LAN  

interface (br-lan) MAC address. Typically, this parameter does not need to be  

modified. (e.g. AA:BB:CC:DD:EE:FF)  

© Copyright 2023 TRENDnet. All Rights Reserved.  

9

 

(1 votes, average: 5.00 out of 5)

Loading...

• ALL WI-FI INSTRUCTIONS & USER MANUALS
• TRENDnet

Questions and Answers (0)

If you have any questions regarding TRENDNET AX1800 Dual Band Wifi 6 Gigabit Dual Wan VPN SMB Router User Guide, please ask here and describe the problem in detail.